Lettura libera · account gratuito per contribuireErede di Anticars (2000)

BMW M3

1986– · 6 generazioni · 15 difetti documentati · 2 mercati
Generazioni

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
MercatoTuttiNA
E90/92/93 M3 · 2007–2013
BollettinoCriticoElettronicaNA

Bollettino

"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

NHTSA · bollettino del costruttore10146535Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

Butt connector for repairing a plug connection. The ?top up coolant? message is displayed in the central display (CC message ID 166). When checking the cooling system there are no leaks found and the expansion tank is filled to the proper level.

NHTSA · bollettino del costruttore10193494Anni modello 2013Mostrato in inglese originale · traduzione in attesaVedi dettagli →
G80 M3 · 2020–
BollettinoModeratoElettronicaNA

Bollettino

**COMFORT ACCESS E COMFORT GO NON POSSIBILI:** Il veicolo non può essere bloccato/sbloccato o avviato tramite Comfort Access. La funzionalità del telecomando viene ripristinata premendo uno qualsiasi dei tasti della chiave oppure rimuovendo e reinserendo la batteria della chiave telecomando.

NHTSA · bollettino del costruttore10179824Anni modello 2020Tradotto automaticamente · originale: ingleseVedi dettagli →
G80 M3 · 2020–
BollettinoModeratoElettronicaNA

Bollettino

KAFAS04 (CAMERA-BASED DRIVER ASSISTANCE SYSTEMS) LIMITATIONS: Various functions of the KAFAS (without radar installed) are not operating up to customer expectations.

NHTSA · bollettino del costruttore10175290Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
G80 M3 · 2020–
BollettinoModeratoElettronicaNA

Bollettino

COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic discharge puts the remote control key into a deep sleep. Various situations can lead to an electrostatic charge which is often not recognized by the customer. For example walking over carpet wearing shoes that have a hard rubber sole positive and negative charges are exchanged. The sole accumulates a negative charge and an electrostatic charge develops before touching the remote control key.

NHTSA · bollettino del costruttore10174317Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
G80 M3 · 2020–
BollettinoModeratoElettronicaNA

Bollettino

ENGINE DOES NOT START BELOW FREEZING TEMPERATURES: Engine designation correction Parts availability Warranty. The engine will not start at temperatures below freezing. The starter does not turn and engage.

NHTSA · bollettino del costruttore10170572Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · bollettino del costruttore10152310Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bollettino del costruttore10151170Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).

NHTSA · bollettino del costruttore10150389Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."

NHTSA · bollettino del costruttore10150334Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bollettino del costruttore10150033Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bollettino del costruttore10150218Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

BMW Parts Bulletin TEC1T RDC Module Return BMW NA has requested the inspection of the following part numbers: 36 10 6 856 227 and 36 10 6 798 872 Stock should not be sold or installed on any vehicle. Please return the part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC1T must appear in the text of your TEC claim. TEC1T is valid from May 30, 2013, through June 13, 2013.The deadline for filing a claim under TEC1T is June 13, 2013. All parts must be returned to your facing RDC no later than June 27, 2013. Part number 36 10 6 856 227: All parts with an index of 02 and older must be returned. All parts with an index of 03 are correct. Part number 36 10 6 798 872: All parts with an index of 03 and older must be returned. All parts with an index of 04 are correct. The Index is the two digit code under the bar code located on the box label. The Index can also be found on the part itself just after the part number. Please re-order the same part number as needed. (c) 2013, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.

NHTSA · bollettino del costruttore10150084Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."

NHTSA · bollettino del costruttore10149589Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

CLOSED-CIRCUIT CURRENT MONITORING. Increased closed-circuit currents may occur permanently or intermittently and cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control module or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control module will be reset if the battery is disconnected. Following a reset, the faulty control module may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp or 100-amp clip-on probe can be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time.

NHTSA · bollettino del costruttore10149555Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

?SI B12 14 12 April 2013 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 14 12 dated January 2013. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bollettino del costruttore10149339Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

2013 MINI JCW Paddle Shifter Retrofit. SZL to EGS harness installation. For necessary preliminary tasks, refer to ISTA and perform the following steps listed in this document.

NHTSA · bollettino del costruttore10149498Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.

NHTSA · bollettino del costruttore10149349Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
E90/92/93 M3 · 2007–2013
BollettinoModeratoElettronicaNA

Bollettino

N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.

NHTSA · bollettino del costruttore10149296Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

NHTSA · bollettino del costruttore10148173Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.

NHTSA · bollettino del costruttore10148195Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

"Service Action: Replace Engine Compartment Sound Insulation. The sound insulation in the engine compartment does not seal properly. 1.Left side: Turn the locks (1) 90 degrees counterclockwise. Unlock the catch (2) and remove the cover (3). Manufacturing tolerances and a defect in workmanship may cause the sound insulation to leak water into the DME wiring connector. AFFECTED VEHICLES This Service Action involves F80 and F82 vehicles produced from March 18, 2014 to May 20, 2014. First check if a Service Action label with a code number 698 is already attached to the B-pillar. If a code number 698 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

NHTSA · bollettino del costruttore10148031Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

N63: Proper Ignition Harness Installation and Ground Connections. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16511.1.B12241... 10/14/2014 Page 2 of 2 Any consecutive damage to the BSD interface components (DME, alternator voltage regulator, QLT sensor) caused by incorrect reinstallation of the ignition harness is not covered under the BMW New Vehicle /SAV Limited Warranty.

NHTSA · bollettino del costruttore10148021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a high-voltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use in accordance with their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging systems and a simplified tool and battery voltage checking procedure below.

NHTSA · bollettino del costruttore10148035Mostrato in inglese originale · traduzione in attesaVedi dettagli →
F80 M3 · 2014–2018
BollettinoModeratoElettronicaNA

Bollettino

BMW Parts Bulletin TEC9V Fuel Tank / Level Sensor Returns BMW AG has requested an inspection of the following part numbers: 16 11 7 268 031, 16 11 7 268 032 and 16 11 7 297 340 Stock should not be sold or installed on any vehicle. 16 11 7 268 031 and 16 11 7 268 032 All fuel tanks produced before 05/30/2014 needs to be returned. All parts with later dates of production are ok and can be used. 16 11 7 297 340 All level sensors produced in Poland before 05/19/2014 (date is shown as day 139 of year 14 on the part) need to be returned. Those produced after this date are ok and can be used. All level sensors produced in Brazil currently in dealer inventory need to be returned. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC9V must appear in the text of your TEC claim. TEC9V is valid from September 24, 2014, through October 08, 2014. The deadline for filing a claim under TEC9V is October 08, 2014. All parts must be returned to your facing RDC no later than October 22, 2014. Please re-order the same part numbers as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution. Page 2 / 2 Made in Poland Made in Brazil Need to be returned (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.

NHTSA · bollettino del costruttore10148044Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).