Bollettino
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Cadillac CTS (tutte le generazioni)
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
This engineering Information (EI) ends the need for information from the field for a condition of oil leaking from the valve rocker arm oil control valve. If a vehicle is encountered with this condition, refer to SI for further diagnosis.
This engineering information PI ends the need for information from the field on a oil leak from the oil pan.
This engineering information PI ends the need for information from the field on a oil leak from the oil pan.
This technical bulletin provides a procedure to replace the crankshaft bearings and rear oil seal to correct the customers concer of an oil leak.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
This technical bulletin provides repair information for replacement of the drive belt tensioner to correct a customer concern for a rattle noise at 48 km/h (30 mph) to 64 km/h (40 mph) when the engine is switching between V4 and V8 and/or they notice fluid leaking from the bellow on top of the tensioner.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
This technical bulletin provides a procedure to install a anti rattle spring on the actuator arm for the turbo and to correct the customers concern of a rattle noise heard from front of the engine.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
This preliminary information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.00150.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that mating surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
Cadillac/chevrolet: See document search button for owner letter. Diagnostic system is incorrectly indicating leakage in fuel evaporative system due to evaporative emission canister vent solenoid valve failing to close properly. Model 2012 cts, camaro. *pe updated 6/16/15. *pe
Gm: The engine may be leaking from the front cover or oil filter adapter. This is not a recall. *js
Chevrolet/cadillac: Procedures for replacing evaporative emission canister vent solenoid (cvs) valve, in closed position, that is not fully sealed and indicates a false leakage. In diagnostic system. Model 2012 cadillac cts, chevrolet camaro. *pe
Coolant leak from head cup plugs on gen iii engines. *mr
3.6l ly7 engine- engine oil leak. *mr
3.6l ly7 engine, intermittent stall setting a diagnostic trouble code (dtc) p0336. *tt
This service bulletin provides a service procedure to correct a condition of a Ticking Noise from the Engine.
Engine Exchange Program for 2014 Model Year Has Ended.
Engineering Information.
Engineering Information.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).