Bollettino
This service bulletin provides a procedure to replace the FPDCM if found to cause customers concerns of Crank No Start, Stalling, Malfunction Indicator Lamp (MIL) Illuminated DTC P023F or P129F Set.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Chevrolet Express
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
This service bulletin provides a procedure to replace the FPDCM if found to cause customers concerns of Crank No Start, Stalling, Malfunction Indicator Lamp (MIL) Illuminated DTC P023F or P129F Set.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
This service bulletin provides a procedure to replace the FPDCM if found to cause customers concerns of Crank No Start, Stalling, Malfunction Indicator Lamp (MIL) Illuminated DTC P023F or P129F Set.
Questa comunicazione informativa preliminare fornisce informazioni al tecnico sui veicoli che presentano un problema intermittente di assenza di motore, niente avviamento o avviamento con la spia di sicurezza accesa. Il tecnico può trovare i codici diagnostici B3055, B3060 e/o B3935. Il tecnico non dovrebbe sostituire alcun componente per questo problema. Se non è possibile duplicare il problema, chiedi al cliente se il cliente utilizza dispositivi di identificazione a radiofrequenza quando il problema è presente. Il concessionario dovrebbe anche indirizzare i clienti alla sezione appropriata nel manuale del proprietario che indica la conformità del dispositivo.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
This informational bulletin provides information for dealers/technicians on Illuminated Check Engine Light, Possible Water in the Fuel, Evaporative Codes Set, Fuel Tank Evaporative Vent Valve Leak.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Technician will need to reference the latest version of General Motors Up-fitter Integration Bulletin 151. The information can be found at http://www.gmupfitter.com/ under the "Technical Bulletin" Tab and then "Show all bulletins."
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
No Crank/No Start, Batteria scarica a causa di assorbimento o scarica parassita.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
This Preliminary information communication provides information to the technician on installing Regular Production Option Code UVC Rearview Camera. Technician will need to reference the latest version of General Motors Up-fitter Integration Bulletin 151. The information can be found at http://www.gmupfitter.com/ under the "Technical Bulletin" Tab and then "Show all bulletins."
This Preliminary information communicates to the dealer an issue where the vehicle's inspection and maintenance monitors along with diagnostic trouble codesmay reset unprompted due to the installation of an aftermarket fuel pump control module.
16056-01 Customer Satisfaction Program. Bulletin Resumed and revised to include inspection to dealer inventory on certain vehicles ordered with a base radio with optional USB port (RPO U0H), may have been built without the port installed. Replace Monroney label on stock vehicles with corrected label. Customer option to install USB outlet assembly, or receive a $100 USD/$135 CDN reimbursement.
16056 Customer Satisfaction Program. Certain vehicles ordered with a base radio with optional USB port (RPO U0H), may have been built without the port installed. Replace Monroney label on stock vehicles with corrected label. Customer option to install the USB outlet assembly, or receive a $100 USD/$135 CDN reimbursement
16005 -Service Update. Certain vehicles may have been built with an incorrect headliner that includes a provision for interior lighting. This condition causes open holes and loose wiring connectors in the headliner to be visible to the customer. Additionally, the service parts identification (SPID) label contains an incorrect headliner RPO code. Dealers will install a new SPID label and, if necessary, replace the headliner.
17139 - Service Update. Certain vehicles may have delamination on the electronic control module (ECM) printed circuit board (PCB) causing open circuits. This condition may result in possible no start or stall. Dealers are to replace and reprogram the ECM.
This Preliminary Information communication provides information to the technician that when the installation of the navigation map update outlined in bulletin 16NA328 or after, may encounter an Invalid Product Update message. Technician will need to gather scan tool data, software numbers and error messages. Technician will need to contact General Motors Technical Assistance Center with the information for further assistance.
This Preliminary Information communication provides information to the technician that when the installation of the navigation map update outlined in bulletin 16NA328 or after, may encounter an Invalid Product Update message. Technician will need to gather scan tool data, software numbers and error messages. Technician will need to contact General Motors Technical Assistance Center with the information for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
15169 - customer satisfaction program. Certain vehicles may exhibit a condition in which the vehicle engine will crank but not start. A reversed wire in the engine egi harness can lead to an ignition sneak circuit, which can prevent the engine control module from commanding a spark at start-up. During the crank / no start event, a malfunction indicator lamp will be illuminated, and the vehicle will store the following code: U0100, u1000, and b2193. Dealers are to revise the engine egi harness.
15169a - customer satisfaction program (revised to update the crimping tool number in the service procedure). Certain 2015 model year chevrolet city express model vehicles may exhibit a condition in which the vehicle engine will crank but not start. A reversed wire in the engine egi harness can lead to an ignition sneak circuit, which can prevent the engine control module from commanding a spark at start-up. During the crank / no start event, a malfunction indicator lamp will be illuminated, and the vehicle will store the following code: U0100, u1000, and b2193. Dealers are to revise the engine egi harness.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).