Motorrijtuigen - carrosserie (beschermingsmiddelen inzittenden)
Bij de betrokken auto's is kan het stiksel van de gesphouders van de veiligheidsgordels achter mogelijk los komen.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Citroën C1 (tutte le generazioni)
Bij de betrokken auto's is kan het stiksel van de gesphouders van de veiligheidsgordels achter mogelijk los komen.
It has been identified that during the fuel tank production process the joint between the tank and the fuel supply pipe assembly may not have been produced to the correct standard. Should this indeed be the case leakage from the supply pipe area of the fuel tank might occur.
La couture des boucles arrière de la ceinture de sécurité pourrait être défectueuse. cela affectera la fonction de protection de la ceinture de sécurité, ce qui augmentera le risque de blessure en cas d’accident.
The stitching of the rear seat-belt buckles could be defective.This will impair the seat belts' protective function, increasing the risk of injury in the event of an accident.
On affected vehicles some rear seat belts may have incorrect stitching on the belt material to connect the buckle to the anchor plate.
Due to an error in the fuel tank production process, the tank may rupture and leak. As a consequence, fuel may spill onto the road and create a hazard for following traffic.
De achterportierruit is mogelijk niet correct gelijmd.
ステアリングコラムシャフトとステアリングギアボックスを接続するボルトの取付けが不適切なため、当該取付部の結合力が不足しているものがある。そのため、かじ取り操作等により当該取付部が分離して、最悪の場合、かじ取り操作ができなくなるおそれがある。
It is possible that the glue that adheres the windowpane to the rear door could come loose. In this event the pane would be fixed at only one point and could drop onto the road.
On the affected vehicles the bonding of the rear door window glass to the hinge assemblies may not conform to specification.
null Part of the steering column assembly could fail, which could lead to loss of control of the vehicle.
A component of the steering column may not be to specification and could fail. If this occurs there would be a loss of directional control.
null There is a risk of the front shock absorber rods breaking which could lead to loss of control of the vehicle and an accident.
Affected vehicles may have a small defect in the front bumper frame. This may affect its impact absorption in the even of a collision.
The front shock absorber rod may have an internal fault which could cause it to brake. This could have an adverse affect on the front suspension and the driver's ability to control the vehicle.
null Owing to a defective welded joint on the rear-axle cross-member, the weld seam may tear and result in loss of control of the vehicle.
On subject vehicles a weld on the rear cross member might be non-compliant and eventually cause the weld between the cross member and the vehicle body to break. This may lead to a partial detachment of the axle and cause the driver to lose control.
It has been established that the con-rod (big end) shell bearings may not have been manufactured to specification. This could lead to premature deterioration of the shells and if not identified it could result in engine failure.
The left hand side front chassis may have a nonconformity which may lead to a risk of poor securing of the suspension arm.
Due to incorrect machining it is possible that the crankshaft is not to the correct specification which can lead to insufficient lubrication of the crankshaft and subsequent engine failure.
It has been identified that within the mechanism of the accelerator pedal there is a friction lever which interacts with a sliding surface. Over time and under certain conditionsthe contact surfaces may generated excessive friction and latterly the movement of the accelerator pedal. This over time and under certain conditions will result in the accelerator pedal becoming intermittently more difficult to push; or slower to return. In rare instances the accelerator pedal can remain in the partially depressed position.
A possible substandard tapping of one or more of the wheel stud holes may result in a reduction of the wheel stud to hub torque setting.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).