Bollettino
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Fiat 124 Spider (tutte le generazioni)
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
Il reclamo del cliente può includere una perdita o un consumo di olio motore
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaftis replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft,it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft-PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
RKE Unlock Operates, Vehicle Only Starts With Key Pressed Into The Keyless Push To Start Button
Blind Spot Or Park Assist Warnings, False Activation
Preoccupazione per lo scaricamento della batteria, assorbimento normale della doppia porta USB, illuminazione prolungata o funzionamento prolungato dopo lo spegnimento con chiave
Customer complaint includes a Mil-on condition. Upon further investigation, one or more of the following fault codes may be set in the PCM:
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
Diagnostic and system improvements.
Diagnostic and system improvements.
Flash: Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P0000-00 - Will be displayed but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance). The customer may notice one of the following condition(s):Incorrect ambient temperature readings on the Instrument Panel Cluster (IPC). Engine knock issues. In addition, the following software enhancement is also available:4-3 and 3-2 downshift improvements.
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P0000-00 - Will be displayed but should really be displaying P0326-00 (Knock Sensor 1 Circuit Performance). The customer may notice one of the following condition(s):Incorrect ambient temperature readings on the Instrument Panel Cluster (IPC). Engine knock issues. In addition, the following software enhancement is also available:4-3 and 3-2 downshift improvements.
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
Radio Pre-Authorization Program - Select 7.0/8.4/8.4N Radios (New and Exchange) - 2018 Model Year Vehicles
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. This software flash will allow an increase to the speed control set speed to 180 KPH (112 MPH) calibration.
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).