Impianto elettrico:Accensione
L'interruttore di accensione potrebbe subire un cortocircuito interno.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Ford F-Series eighth generation
L'interruttore di accensione potrebbe subire un cortocircuito interno.
Un cortocircuito potrebbe verificarsi nell'interruttore di accensione, con conseguente surriscaldamento, fumo e possibile incendio nel piantone dello sterzo del veicolo. Questa condizione può verificarsi sia mentre il veicolo è in uso sia quando è incustodito. Correzione: l'interruttore di accensione sarà sostituito con un interruttore di nuova progettazione.
Note: Vehicles equipped with 7.5 litre engines. The fuel return tube, which connects the frame fuel return line with the engine fuel rail, may contact the pinch weld flange connecting the dash panel to the floor pan. This could lead to abrasion of the steel tube and result in a fuel leak. Correction: Fuel return tubes will be replaced with flexible stainless steel braided/teflon lines and a vinyl guard will be installed on the body weld flange.
The steel fuel return tubes that connect the frame fuel return lines with the engine fuel rail can contact the pinch weld flange connecting the dash panel to the floor pan. Continued contact leads to abrasion of the steel fuel return tube and eventually results in a fuel leak.
A malfunctioning check valve within the fuel pump assembly causes a portion of the unused fuel from one tank to be returned to the second tank. When this occurs, the capacity of the second tank can be exceeded, causing fuel spillage.
Vehicles with gasoline engines and dual fuel tanks may experience the transfer of fuel from one tank to the other through a malfunctioning check valve within the fuel pump assembly. This could cause the capacity of the other tank to be exceeded, resulting in fuel overflow past the filler cap. In the presence of an ignition source, a fire could result. Correction: Fuel pressure regulator will be replaced and redundant check valves will be installed on affected vehicles.
Keys attached to the key ring of an ignition key while it is in the vehicle ignition can become lodged in the steering lock receiver as the steering wheel is being turned.
On vehicles with dual fuel tanks, the dual function fuel reservoir (dfr) may malfunction allowing supply fuel to be drawn from one tank and a portion of the unused fuel to be returned to the other tank. As a result, the other tank could possibly be overfilled, resulting in overflow of fuel past the filler cap. In the presence of an ignition source, the potential for a fire may exist. Correction: A dfr containing "o" rings manufactured from revised material will be installed on affected vehicles.
The dual fuel tank selector valve may malfunction and cause an overfill condition in one of the fuel tanks, resulting in an overflow of fuel past the filler cap.
Note: This recall supersedes recall 88164. Vehicles located in the yukon, nothwest territories, alberta, eastern british columbia, n.W. Ontario, manitoba and saskatchewan. A short, u-shaped nylon fuel tube (jumper tube) located on the left-hand frame rail connecting the fuel pump to the fuel filter could develop pin holes in the tubing wall. If this condition should occur, it would allow fuel to leak and a fire could result. Correction: A steel braided teflon fuel supply line and related components will be installed which will ground the fuel line and eliminate the potential for an electrostatic charge. The u-shaped nylon jumper tube will be eliminated by this replacement fuel system.
Incorrectly installed fuel line connectors have fuel supply and return lines crossed.
Bolts that attach the front axle track bar bracket to the front crossmember may loosen, allowing the front wheels to oscillate with front end shimmy.
A short, u-shaped nylon fuel tube (jumper tube) located on the left-hand frame rail connecting the fuel pump to the fuel filter could develop pin holes in the tubing wall. If this condition should occur, it would allow fuel to leak and a fire could result. Correction: Fuel tube will be replaced with one having a krayton sleeve.
Steering/suspension systems may not adequately control steering type wobble allowing the front end to shimmy.
On vehicles with EFI or CFI, the spring-lock fuel line coupling used to connect the fuel supply and return lines to the EFI fuel rails or to the CFI throttle bodies, as well as other fuel line connections near the dash panels on some vehicles, could disengage during vehicle use. Should this occur, loss of fuel will result, providing the potential for a vehicle fire. Correction: Coupling retainer clips will be installed on affected vehicles. Note: Escort vehicles are equipped with EFI and CFI. Lynx vehicles are equipped with CFI only. EFI - electronic fuel injection; CFI - central fuel injection
Wheel lug nut cone angles do not match lug nut seating angles.
Spring lock fuel line coupling may not be properly engaged.
Trucks fail to meet requirement of fmvss no. 301, fuel system integrity, in a 30 mph front angular barrier test impact because of the omission of the nose shield on midship fuel tank. Consequence of defect: In case of an accident, fuel spillage in the trucks which do not meet the fmvss increases the risk of a fire.
Alcuni dei veicoli interessati potrebbero essere dotati di un cavo del cruise control che può interferire con la puleggia del servocomando del cruise control, impedendo alla farfalla di tornare al minimo quando si disinserisce il cruise control.
Nota: include anche alcuni autocarri medi e pesanti. Questi veicoli potrebbero non essere conformi alla norma C.M.V.S.S. 108 - illuminazione. Il modulo delle luci diurne (DRL) potrebbe malfunzionare, causando luci diurne che si attenuano, lampeggiano o si spengono oppure, in alcuni casi, rimangono accese dopo lo spegnimento del quadro. Correzione: il modulo delle luci diurne sarà sostituito sui veicoli interessati.
Note: Vehicles with 7.3 litre diesel and 7.5 litre efi engines over 8500 lb. Gvwr and 4x4 models with 5.8 litre efi engines. When vehicles are operated at or near gvwr or gcwr (gross combination weight rating when trailer towing), brake effectiveness may diminish due to overheating of the front brakes. This may result in longer than normal stopping distances and a low brake pedal and could increase the risk of a vehicle crash. Correction: Snap-in insulators that attach to each of the front brake caliper pistons will be installed on all affected vehicles. In addition, vehicles equipped with 7.5 litre engines will have insulation installed on engine compartment brake lines.
The throttle cable which runs from the accelerator to the governor assembly housing may have been kinked during assembly, causing excessive wear of the cable housing inner lining. This could result in either fracture or sticking of the cable.
Lower end of brake rod, which connects brake pedal arm to bell crank of power brake assebly, may have inadequate wall thickness.
These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. Vehicles may have fuel tank vapour hose that is too long and may be kinked near the connection to the evaporative emissions canister. Correction: Hoses will be inspected and length reduced if necessary.
Note: Vehicles equipped with 7.5 litre engines. These vehicles do not comply with c.M.V.S.S. 1103 - exhaust emissions. Incorrect egr valve. Correction: Egr valve will be replaced.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).