Impianto elettrico:Accensione
L'interruttore di accensione potrebbe subire un cortocircuito interno.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Ford EXP (tutte le generazioni)
L'interruttore di accensione potrebbe subire un cortocircuito interno.
Un cortocircuito potrebbe verificarsi nell'interruttore di accensione, con conseguente surriscaldamento, fumo e possibile incendio nel piantone dello sterzo del veicolo. Questa condizione può verificarsi sia mentre il veicolo è in uso sia quando è incustodito. Correzione: l'interruttore di accensione sarà sostituito con un interruttore di nuova progettazione.
On i modelli 1984, potrebbero svilupparsi crepe esterne nelle teste dei cilindri del motore, che potrebbero causare una perdita d'olio sul collettore di scarico. Sui modelli 1985, la guarnizione del coperchio punterie del motore potrebbe spaccarsi, con il rischio che l'olio fuoriesca sul collettore di scarico. Entrambe queste condizioni creano la possibilità che l'olio prenda fuoco, causando un incendio nel vano motore. Correzione: sui modelli 1984, le teste dei cilindri verranno ispezionate e sostituite se risultano presentare crepe esterne. Sui modelli 1985, le guarnizioni del coperchio punterie verranno ispezionate e sostituite, a meno che non siano di un modello più recente.
External cracks above the number 3 cylinder (1984 models) or rocker arm cover gaskets splitting (1985 models) could allow oil to leak onto the exhaust manifold. Nota: la traduzione richiesta è la seguente: Crepe esterne sopra il cilindro numero 3 (modelli 1984) o rotture delle guarnizioni del coperchio dei bilancieri (modelli 1985) potrebbero consentire la fuoriuscita di olio sul collettore di scarico.
I veicoli potrebbero presentare un gioco insufficiente tra i tubi del freno anteriore destro e una staffa montata sul motore. In determinate condizioni, la staffa potrebbe entrare in contatto con il tubo del freno in metallo e provocarne l'abrasione, con conseguente perdita di liquido dei freni e perdita parziale della frenata. Ciò comporterebbe un aumento delle distanze di arresto.
The front sleeve bushings of the cooling fan motors are susceptible to excessive corrosion in areas of high road salt use. This may increase the rotational friction of the fan motor or result in seizure of the armature shaft to the bushing. Either condition may draw current in excess of that of a normally operating motor but less than required to operate the fuse link. This could overheat the motor wiring circuitry and possibly result in an underhood or instrument panel fire. Vehicles affected: Cars not equipped with factory air conditioning. Quebec and atlantic provinces only.
Questi veicoli potrebbero non essere conformi alla norma C.M.V.S.S. 1103 - emissioni di gas di scarico. L'iniettore di carburante centrale (cfi) potrebbe funzionare con miscela ricca in determinate condizioni di esercizio. Correzione: verranno installati iniettori di carburante cfi migliorati e il regime del minimo sarà regolato.
These vehicles do not comply with cmvss 1103 - exhaust emissions. Vehicles affected: 1.6 l engine and atx transmissions
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
Two door models. Fatigue cracks may occur in the door lock pillars at the front door latch striker reinforcement attachment locations. The fatigue cracks may propogate to the extent that the structural integrity of the door latch striker attachment may be significantly reduced creating the possibility that the door may not be securely retained. This condition is observable by visibly noticeable cracks on the door lock pillar adjacent to the striker assemblies.
Door lock pillars could develop fatigue cracks from normal usage of door, at the point where door latch striker reinforcements are attached.
On the involved vehicles, a thermal limiter in the blower motor resistor circuit of the air conditioner/heater assembly may not function as intended. If the blower motor becomes jammed when the system is operating in the medium-low blower speed, the resistor coils can overheat causing melting and possible ignition.
Vehicles with optional air conditioning. The air conditioner blower motor thermal limiter may not operate as intended when there is a motor blockage or malfunction. Thus, if the blower motor becomes jammed when the system is operating in the medium-low blower speed mode, the resistor coils may overheat causing melting and possible ignition of the polyproplene evaporator housing with associated vehicle damage.
Vehicles equipped with power brakes. Power brake boosters may have bewen improperly assembled by supplier. Mis-indexing of rear shell of some boosters relative to the front shell may have resulted in inadequate crimping of the two shells. If booster were to separate during vehicle operation, complete loss of service brakes would result.
Some vehicles equipped with power brake boosters have front and rear shells that may have been improperly joined. Improperly joined booster shells may separate either partially or completely during brake application.
Vehicle may not meet the fuel spillage requirements of cmvss 301 - fuel system integrity.
Certain vehicles may not meet applicable minimum fuel spillage requirements of federal motor vehicle safety standard no. 301, "fuel system integrity". During a 30 mph rear impact test, fuel spillage limits were exceeded by vehicle.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0).