Lo stelo della valvola di controllo del riscaldatore non rispetta le specifiche sui materiali. Temperature elevate del liquido di raffreddamento possono causare perdite dallo stelo.
NHTSA · Stati Uniti6 giu 199494V103000Anni modello 1988–1989Tradotto automaticamente · originale: ingleseVedi dettagli →
I veicoli non hanno superato i requisiti del test d'urto laterale con barriera mobile della normativa FMVSS 301, "integrità del sistema di alimentazione del carburante". La perdita di carburante dal serbatoio ha superato la quantità massima di fuoriuscita consentita.
NHTSA · Stati Uniti23 nov 199393V192000Anni modello 1990–1994Tradotto automaticamente · originale: ingleseVedi dettagli →
Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.
Transport Canada30 dic 19911991176Anni modello 1988–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086
Transport Canada18 apr 19861986044Anni modello 1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which can cause an open circuit at high operating temperatures. This can cause the vehicle to stall.
NHTSA · Stati Uniti11 mag 199494V090000Anni modello 1994Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Le trasmissioni manuali possono bloccarsi a causa di una lubrificazione insufficiente degli ingranaggi nel carter della trasmissione. Ciò può far grippare le ruote motrici e causare un arresto improvviso del veicolo.
NHTSA · Stati Uniti4 ott 199393V167000Anni modello 1986–1989Tradotto automaticamente · originale: ingleseVedi dettagli →
Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.
NHTSA · Stati Uniti31 dic 199191V225000Anni modello 1986–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.
Transport Canada18 mag 19901990072Anni modello 1990Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.
Transport Canada27 nov 19871987127Anni modello 1986–1987Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.
Transport Canada29 mar 19861986033Anni modello 1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.
NHTSA · Stati Uniti17 mar 198686V043000Anni modello 1986Mostrato in inglese originale · traduzione in attesaVedi dettagli →
If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.
NHTSA · Stati Uniti19 giu 198989V100000Anni modello 1986–1989Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).