Problema: Questo richiamo riguarda alcuni kit di riscaldamento a blocco installati su determinati veicoli o venduti come accessori nelle concessionarie Toyota o Lexus. Su alcuni veicoli, il cavo del riscaldatore a blocco motore potrebbe non avere sufficiente protezione termica e essere danneggiato dalle alte temperature. Se ciò accade, il cavo potrebbe andare in corto circuito mentre è collegato e causare il surriscaldamento o la scioglimento dei cavi. Nota: Questo richiamo riguarda solo i seguenti numeri di parte del riscaldatore a blocco/cavi: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Rischio per la sicurezza: Cablaggi del riscaldatore motore che si surriscaldano o si sciogliono potrebbero creare il rischio di incendio. Azioni correttive: Toyota raccomanda di smettere immediatamente di usare il riscaldatore a blocco motore. Toyota avviserà i proprietari per posta e ti ordinerà di portare il veicolo da un concessionario per disattivare il riscaldatore a blocco motore. Per alcuni veicoli, le azioni correttive per questo richiamo sono in fase di sviluppo. Per altri, non può essere installato un nuovo riscaldatore a blocco motore e il proprietario riceverà un rimborso del prezzo di acquisto del riscaldatore a blocco motore.
Transport Canada24 nov 20212021723Anni modello 2006–2018Tradotto automaticamente · originale: ingleseVedi dettagli →
On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.
Transport Canada20 lug 20172017363Anni modello 2016–2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
The fuel pressure sensor may not have correctly tightened during assembly. Over time this may affect the seal and allow fuel odour to escape. This could ignite in the presence of an ignition source.
DVSA · Regno Unito26 mag 2016R/2016/080Anni modello 2005–2007Mostrato in inglese originale · traduzione in attesaVedi dettagli →
null The sealing performance of the gasket seated between the fuel pressure sensor and the engine fuel delivery pipe could degrade over time. If this occurs, fuel could leak which, in the presence of an ignition source, could lead to a vehicle fire.
Safety Gate · UE21 apr 2016A12/0512/16Anni modello 2005–2007Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Il guarnizione del sensore di pressione del carburante può deteriorarsi e consentire la fuoriuscita di carburante nel vano motore. In presenza di una fonte di accensione, il rischio di incendio aumenta.
DVSA · Regno Unito24 nov 2014R/2014/135Anni modello 2007–2010Tradotto automaticamente · originale: ingleseVedi dettagli →
In the front wipers on subject left hand drive cars there is high friction at the tightening surface between the wiper arm nut and the wiper arm that could result in the nut being insufficiently tight. If the movement of the wiper arm is restricted by an external load such as a build up of heavy snow on the windshield the wiper motor torque may exceed the wiper arm slipping torque and one or both wipers could become inoperative. If this happens then visibility could be reduced which could increase the risk of a crash.
DVSA · Regno Unito26 apr 2013R/2013/015Anni modello 2007–2010Mostrato in inglese originale · traduzione in attesaVedi dettagli →
null The wiper arm nuts on the front wipers may be insufficiently tight. If the movement of wipers is restricted by an external load, such as a build-up of heavy snow on the windscreen, the wiper motor torque may exceed the wiper arm slipping torque, and one, or both, of the wipers could become inoperative. If this occurs, driver visibility could be reduced, which could lead to an accident.
Safety Gate · UE1 feb 2013A12/0166/13Anni modello 2010–2013Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Toyota is recalling certain model year 2006-2012 Lexus IS250 and IS350 vehicles manufactured August 23, 2005, through October 5, 2011; 2010-2012 Lexus IS250C and IS350C vehicles manufactured April 10, 2009, through October 6, 2011; and 2008-2011 Lexus IS-F vehicles manufactured December 14, 2007, through July 10, 2011. The nuts that fasten the wiper arms may be insufficiently torqued such that if the wiper arms are restricted by an external load, such as a buildup of heavy snow, one or both of the wipers may become inoperative.
NHTSA · Stati Uniti30 gen 201313V030000Anni modello 2006–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).