Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Mazda MX-30

2020– · 1 difetti documentati · 4 mercati

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
BollettinoModeratoCarrozzeriaNA

Bollettino

DESCRIPTION Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. Door outer handle touch sensor for locking (1) / unlocking (2) NOTE: If the concern occurs after specific operation as described below, refer to the TSB 09-046/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND UNLOCK AFTER A SPECIFIC OPERATION). 1. [MX-30] After using cabin preconditioning or hazard warning lights for approx.15 minutes. 2. [MAZDA3 and CX-30] After using hazard warning lights for approx. 15 minutes. 3. [MAZDA3, CX-30 and MX-30] When both touch sensors are touched at once. Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify customer concern. 2. Repair the vehicle depending on the experienced symptom(s). Symptom 1: Follow the "Procedure to waterproof a touch sensor below to make the touch sensor waterproof. Symptom 2: Replace the front outer handle with a modified one according to the instructions on MGSS. Mazda3 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) CX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) MX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) If both symptoms are experienced: Replace the front outer handle with a modified one and follow the Procedure to waterproof a touch sensor below to make the touch sensor waterproof. NOTE: DO NOT repair the other front outer handle for the vehicle if it is not experiencing any problems. 3. Verify the repair by checking if the new outer handle locks/unlocks the door correctly.

NHTSA · bollettino del costruttore11030603Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · bollettino del costruttore10252505Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified

NHTSA · bollettino del costruttore10244579Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified.

NHTSA · bollettino del costruttore10233659Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · bollettino del costruttore10226892Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.

NHTSA · bollettino del costruttore11016214Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

NHTSA · bollettino del costruttore11009639Anni modello 2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

NHTSA · bollettino del costruttore11007022Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · bollettino del costruttore10254183Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may exhibit a rattle noise near the drivers and/or passengers head rests at the B-pillar area while driving on rough roads. This is caused by an interference between the rear end of the front door glass run-channel and the front end of rear sash molding.

NHTSA · bollettino del costruttore10252373Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · bollettino del costruttore10246137Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.

NHTSA · bollettino del costruttore10240403Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.

NHTSA · bollettino del costruttore10240399Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may exhibit the warning message "Ultrasonic Sensor Malfunction" in the instrument cluster and the following DTC(s) stored after replacing the front and/or rear ultrasonic sensor(s) during body or paint repair.

NHTSA · bollettino del costruttore10238672Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

NHTSA · bollettino del costruttore10233683Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

NHTSA · bollettino del costruttore10232303Anni modello 2022–2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. - Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. - Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. - Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. - Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified.

NHTSA · bollettino del costruttore10226856Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may complain about any of the following: * Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. * Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF * MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\"

NHTSA · bollettino del costruttore10225727Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.

NHTSA · bollettino del costruttore10225724Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may experience the MyMazda App not communicating to the vehicle properly which may result in the condition monitor information is not refreshed or remote door lock/unlock not functioning. This is caused by a failure in communication between the telematics communication unit and the MyMazda App. To correct this issue, the control software of the telematics communication unit has been modified.

NHTSA · bollettino del costruttore10222572Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may exhibit the fuel-filler or charge lid opening unintentionally when unlocking the front doors using the door lock switch, the touch sensor on the outer door handle, or the remote transmitter. This is caused by a mechanical issue at the actuator of the fuel-filler/charge lid (when the fuel filler/charge lid is pushed hard, the guide pin in the actuator comes off). To eliminate this concern, the durability of the guide pin in the actuator has been improved.

NHTSA · bollettino del costruttore10222571Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector. Some Mazda3, CX-30 and MX-30 customers may complain that the vehicle door locking system does not work when the door lock switch on the liftgate interior trim is pressed. DTC B11C4:23 (BCM - liftgate lock switch circuit malfunction) may be stored. This may be caused during a high pressure car wash and/or condensation. Water may enter through the rear center brand emblem base component and drip onto the switch connector causing corrosion. The rusted connector may also cause a battery drain. To eliminate this concern, the rear center brand emblem base has been modified to prevent water entry (Mazda3) and the rear harness has been modified to prevent water infiltration (Mazda3, CX-30 and MX-30).

NHTSA · bollettino del costruttore10218727Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may experience the MyMazda App not communicating to the vehicle properly which may result in the condition monitor information is not refreshed or remote door lock/unlock not functioning. This is caused by a failure in communication between the telematics communication unit and the MyMazda App. To correct this issue, the control software of the telematics communication unit has been modified.

NHTSA · bollettino del costruttore10218733Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some vehicles may exhibit a rattle noise near the drivers and/or passengers head rests at the B-pillar area while driving on rough roads. This is caused by an interference between the rear end of the front door glass run-channel and the front end of rear sash molding. To eliminate this concern, the front end of the rear sash molding has been modified to reduce the contact friction with the front door glass run channel.

NHTSA · bollettino del costruttore10218736Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Some customers may complain about any of the following: - Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. - Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF - MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Confirm the customer's phone and vehicle have good to strong reception during the concern as shown in the table below. - If the reception is weak, move the vehicle to a location where the reception is good to strong as shown in the table, then try to get the Authorization Code and/or operate the remote functions before proceeding to the Repair Procedure if there is still an issue. - If the reception is good to strong, proceed to the Repair Procedure.

NHTSA · bollettino del costruttore10219228Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).