I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
DESCRIPTION Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. Door outer handle touch sensor for locking (1) / unlocking (2) NOTE: If the concern occurs after specific operation as described below, refer to the TSB 09-046/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND UNLOCK AFTER A SPECIFIC OPERATION). 1. [MX-30] After using cabin preconditioning or hazard warning lights for approx.15 minutes. 2. [MAZDA3 and CX-30] After using hazard warning lights for approx. 15 minutes. 3. [MAZDA3, CX-30 and MX-30] When both touch sensors are touched at once. Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify customer concern. 2. Repair the vehicle depending on the experienced symptom(s). Symptom 1: Follow the "Procedure to waterproof a touch sensor below to make the touch sensor waterproof. Symptom 2: Replace the front outer handle with a modified one according to the instructions on MGSS. Mazda3 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) CX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) MX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) If both symptoms are experienced: Replace the front outer handle with a modified one and follow the Procedure to waterproof a touch sensor below to make the touch sensor waterproof. NOTE: DO NOT repair the other front outer handle for the vehicle if it is not experiencing any problems. 3. Verify the repair by checking if the new outer handle locks/unlocks the door correctly.
NHTSA · bollettino del costruttore11030603Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.
NHTSA · bollettino del costruttore11003361Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers
NHTSA · bollettino del costruttore11003356Anni modello 2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.
NHTSA · bollettino del costruttore10254184Anni modello 2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.
NHTSA · bollettino del costruttore10252505Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified
NHTSA · bollettino del costruttore10244579Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA02_11046). Ver. 7000C0A-NA02_11046 fixes these software errors (bugs): The system does not resume the play list after editing a play list for an USB audio device. The screen does not show proper picture when receiving SiriusXM data. Ver. 7000C0A-NA02_11044 fixes these software errors (bugs): Beep sounds every couple of minutes. Language setting may not be accepted correctly. When refusing the incoming call while playing audio tracks using the Apple CarPlay, the screen shows Phone in use message and it stops playing audio tracks. The audio track may not pause when pressing the mute button. The screen freezes when smartphone receives messages under Bluetooth connection. Ver. 7000C0A-NA02_11036 fixes these software errors (bugs): Screen freezes and goes to white screen, then the system reboots. Cannot control the audio system with steering switches and command switch. If another incoming call comes in immediately after the hands-free call is ended, the call is automatically accepted. Establishing Bluetooth connection takes tiime. DTC U3000:49 is stored which may be accompanied with following symptoms. -No sound comes out from the speakers. -Audio source selection is unavailable. The vehicle icon rotates when using the navigation with "head-up" mode.
NHTSA · bollettino del costruttore10238677Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
NHTSA · bollettino del costruttore10237206Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified.
NHTSA · bollettino del costruttore10233659Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Alcuni clienti potrebbero lamentare che Mazda Connect non si avvia (schermo nero) oppure che impiega molto tempo per riavviarsi dopo l'accensione del veicolo. Ciò è causato dal fallimento del processo di inizializzazione della CMU all'avvio, dovuto a un componente difettoso sulla scheda elettronica. Per eliminare questo problema, l'hardware interno (DRAM) della CMU è stato migliorato.
NHTSA · bollettino del costruttore10233569Anni modello 2022Tradotto automaticamente · originale: ingleseVedi dettagli →
Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
NHTSA · bollettino del costruttore10232302Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA · bollettino del costruttore10230875Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
NHTSA · bollettino del costruttore10226898Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.
NHTSA · bollettino del costruttore10226892Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).
NHTSA · bollettino del costruttore10225763Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Il sistema di monitoraggio dell'angolo cieco (BSM) può presentare un malfunzionamento con i seguenti sintomi se i sensori radar laterali posteriori sono installati con orientamento errato.
- Il sistema BSM indica la presenza di un veicolo sul lato opposto.
- L'anello indicatore i-ACTIVSENSE non diventa verde.
- L'avviso di traffico posteriore in retromarcia (RCTA) non funziona.
- Sensore radar laterale posteriore
NHTSA · bollettino del costruttore10222563Anni modello 2023Tradotto automaticamente · originale: ingleseVedi dettagli →
Some customers may complain that Mazda Connect does not start or that it takes a long time to restart after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware of the CMU has been improved.
NHTSA · bollettino del costruttore10218768Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.
NHTSA · bollettino del costruttore10218772Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
NHTSA · bollettino del costruttore10213147Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect *Infotainment system software update. *BCM TPMS unlearn during vehicle storage or transport. *Wheel/Tire change
NHTSA · bollettino del costruttore10209755Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.
NHTSA · bollettino del costruttore10208554Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Some vehicle may experience the i-ACTIVSENSE/ALH warning lights on and a system error messages may be found in the center display as well. DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · bollettino del costruttore10206960Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Unexpected Smart Brake Support (SBS-R) Operation Wile Reversing: Some customers may complain about unexpected collision warning or automatic braking while reversing under certain conditions such as a step or object on the road behind the vehicle. This is caused by the control software of the parking assist unit of the Smart Brake Support (SBS-R) unintentionally detecting under certain conditions. To eliminate this concern, the control software of the parking assist unit has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure.
NHTSA · bollettino del costruttore10206010Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
DESCRIPTION Some vehicles may continue to display the recall notification "IMPORTANT NOTICE. VIEW VEHICLE STATUS MONITOR FOR DETAILS" on the center display even after the recall has been completed. NOTE: Once the warranty claim for the recall campaign is approved by Mazda Japan, the recall notification will be automatically removed via Connected Services on the following day or later. This condition may occur if the Connected Services subscription was canceled while the recall notification was still active. ACTION TO BE TAKEN If you encounter the situation above, use MDARS to manually remove the center display recall notification. Note: MDARS can only remove the recall notification when MCVV shows no CV contract.
NHTSA · bollettino del costruttore11037008Anni modello 2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).