Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Mercedes-BenzMercedes-Benz Classe E V213

2016–2023 · 22 difetti documentati · 3 mercati

Questo fascicolo raccoglie i difetti noti della Mercedes-Benz Classe E V213, scritti e documentati dalla comunità. La lettura è libera; un account gratuito permette di contribuire. Un difetto ottiene il sigillo quando abbastanza contributori affidabili lo hanno convalidato.

I proprietari segnalano spesso problemi di engine su quest'auto (93 reclami), ma nessuno ne ha ancora spiegato la causa. La conosci?Scrivi la scheda
I proprietari segnalano spesso problemi di electrical system su quest'auto (84 reclami), ma nessuno ne ha ancora spiegato la causa. La conosci?Scrivi la scheda

Difetti più gravi

Vedi tutto (22) →
m
CriticoMotoreNA

Engine: problems reported by owners

93 owners in the United States reported problems with the engine of this car to NHTSA (model years 2016–2023), typically at around 23,000 miles. Reported consequences: 10 fires, 1 injury.

✓ Analisi Mecafile di dati ufficiali2016–2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
m
CriticoElettronicaNA

Electrical system: problems reported by owners

84 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2016–2023), typically at around 18,000 miles. Reported consequences: 6 fires, 3 injuries.

✓ Analisi Mecafile di dati ufficiali2016–2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
m
CriticoAbitacoloNA

Airbags: problems reported by owners

57 owners in the United States reported problems with the airbags of this car to NHTSA (model years 2016–2019), typically at around 10,000 miles. Reported consequences: 7 crashes, 6 injuries.

✓ Analisi Mecafile di dati ufficiali2016–2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Ultimi richiami ufficiali

Vedi tutto (540) →
RichiamoModeratoCambioKR

동력전달장치 기타

공급업체의 생산 공정의 편차로 인해 시간이 지남에 따라 드라이브 샤프트의 유니버셜 조인트가 마모될 수 있으며, 이로 인해 유니버셜 조인트에서 윤활유 손실이 발생하여 유니버셜 조인트가 파손될 수 있음. 그 결과로 트랜스퍼 케이스와 전륜 구동 장치 간의 연결이 끊어져 추진력을 잃을 수 있고 충돌 위험이 증가할 수 있음이 확인됨에 따른 리콜 <대상차량별 생산일자> S 450 4MATIC: 2018.01.25~2019.11.14 S 560 4MATIC: 2019.08.30~2019.09.12 CLS 400 d 4MATIC: 2019.02.25~2019.04.11 S 350 d 4MATIC: 2019.04.09 E 450 4MATIC: 2019.02.05 S 400 d 4MATIC: 2017.12.11

MOLIT · Corea del Sud30 set 20266389Anni modello 2017–2019Mostrato in coreano originale · traduzione in attesaVedi dettagli →
RichiamoModeratoCambioUK

SRPC2603 - Drive Shaft Joint

Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur.

DVSA · Regno Unito21 set 2026R/2026/148Anni modello 2019Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoCriticoSospensioniEU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw28 ago 2026MGP230033Anni modello 2016Mostrato in olandese originale · traduzione in attesaVedi dettagli →

Ultimi bollettini tecnici

Vedi tutto (488) →
BollettinoModeratoSospensioniNA

Bollettino

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the onboard electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10P1127WT). Note: An adequate voltage from the onboard electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the onboard electrical system battery. 2. Connect diagnostic system (see AD00.00P200006FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view Drive systems N127 "Drivetrain" control unit (CPC) 4. Update software for control unit N127 (CPC) (see AR54.21P001401Y). Info: To do so, select the following menu items: Adaptations Control unit update Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times 5. Disconnect diagnostic device from vehicle (see AD00.00P200006FR). 6. Disconnect charger from vehicle (see AR54.10P1127WT).

NHTSA · bollettino del costruttore11038925Anni modello 2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoLieveCarrozzeriaNA

Bollettino

Denuncia Rumore metallico proveniente dalla zona degli altoparlanti nelle portiere. Causa In fase di analisi. Rimedio Per restringere la causa, rimuovere innanzitutto il rivestimento della portiera. Se il rumore continua a verificarsi anche con il rivestimento della portiera rimosso, proseguire la diagnosi concentrandosi sull'altoparlante e, se necessario, aprire un caso TIPS con un video informativo come allegato. Nota: fare riferimento a questo documento nella richiesta di garanzia e, una volta completata la diagnosi, selezionare il codice di danno in base al componente che causa il problema. Se il rumore si interrompe quando il rivestimento della portiera viene rimosso, procedere in conformità con LI72.10P067691. Informazioni In questo caso, non utilizzare un codice di danno per gli altoparlanti nella richiesta di garanzia!

NHTSA · bollettino del costruttore11038217Anni modello 2018–2023Tradotto automaticamente · originale: ingleseVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

NHTSA · bollettino del costruttore11038188Anni modello 2017–2023Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).