Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Mercedes-BenzMercedes-Benz Classe S W221

2005–2013 · 11 difetti documentati · 6 mercati

Questo fascicolo raccoglie i difetti noti della Mercedes-Benz Classe S W221, scritti e documentati dalla comunità. La lettura è libera; un account gratuito permette di contribuire. Un difetto ottiene il sigillo quando abbastanza contributori affidabili lo hanno convalidato.

I proprietari segnalano spesso problemi di electrical system su quest'auto (45 reclami), ma nessuno ne ha ancora spiegato la causa. La conosci?Scrivi la scheda
I proprietari segnalano spesso problemi di engine su quest'auto (37 reclami), ma nessuno ne ha ancora spiegato la causa. La conosci?Scrivi la scheda

Difetti più gravi

Vedi tutto (11) →
m
CriticoElettronicaNA

Electrical system: problems reported by owners

45 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2006–2012), typically at around 71,000 miles. Reported consequences: 5 fires.

✓ Analisi Mecafile di dati ufficiali2006–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
m
CriticoMotoreNA

Engine: problems reported by owners

37 owners in the United States reported problems with the engine of this car to NHTSA (model years 2006–2012), typically at around 70,000 miles. Reported consequences: 5 fires.

✓ Analisi Mecafile di dati ufficiali2006–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
m
CriticoCambioNA

Transmission and drivetrain: problems reported by owners

31 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 2006–2012), typically at around 67,000 miles. Most often named: automatic transmission (29%). Reported consequences: 2 crashes, 1 fire.

✓ Analisi Mecafile di dati ufficiali2006–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Ultimi richiami ufficiali

Vedi tutto (53) →
RichiamoCriticoSospensioniEU

Motorrijtuigen en aanhangwagens - stuurinrichting

De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.

rdw28 ago 2026MGP230033Anni modello 2013Mostrato in olandese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoSospensioniEU

The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive…

The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive road-grit (salt) used for melting ice. Advanced corrosion could weaken the screws, leading to potential breakage during manoeuvring or parking. If all fixing screws fail, the power-assisted steering could detach, resulting in a loss of power steering and an increased risk of an accident.

Safety Gate · UE17 dic 2024SR/03711/24Anni modello 2010–2013Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoCarrozzeriaEU

The polycarbonate roof panel located between the windscreen and the panoramic roof may not have been…

The polycarbonate roof panel located between the windscreen and the panoramic roof may not have been bonded correctly to the vehicle during a prior repair. In such cases, the adhesive bonding could gradually deteriorate and the panel could become detached from the vehicle, posing a risk to other road users.

Safety Gate · UE22 ago 2024A12/00730/21Anni modello 2012–2013Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Ultimi bollettini tecnici

Vedi tutto (135) →
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

NHTSA · bollettino del costruttore11029959Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoCarrozzeriaNA

Bollettino

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system LI82.10-P-078302 Closed ventilation system LI82.10-P-078304

NHTSA · bollettino del costruttore11029025Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →
BollettinoModeratoSospensioniNA

Bollettino

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

NHTSA · bollettino del costruttore11025648Anni modello 2006Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).