Electrical system: problems reported by owners
35 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2017–2020), typically at around 9,000 miles. Reported consequences: 1 crash, 6 fires.
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Mercedes-Benz X166
Questo fascicolo raccoglie i difetti noti della Mercedes-Benz X166, scritti e documentati dalla comunità. La lettura è libera; un account gratuito permette di contribuire. Un difetto ottiene il sigillo quando abbastanza contributori affidabili lo hanno convalidato.
35 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2017–2020), typically at around 9,000 miles. Reported consequences: 1 crash, 6 fires.
25 owners in the United States reported problems with the engine of this car to NHTSA (model years 2017–2020), typically at around 15,000 miles. Reported consequences: 9 fires, 1 injury.
18 owners in the United States reported problems with the fuel system of this car to NHTSA (model years 2017–2020), typically at around 4,000 miles. Reported consequences: 1 crash, 5 fires, 3 injuries.
De drie aluminium schroeven waarmee de power-pack aan de stuurinrichting is bevestigd, kunnen door blootstelling aan water en strooizout roesten.
엔진의 질소산화물 배출량 개선을 위한 소프트웨어 업데이트에 따른 리콜 <대상차량별 생산일자는 상이할 수 있으므로 자세한 사항은 제작사 고객센터(080-001-1886)으로 문의하여 주시기 바랍니다.>
The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive road-grit (salt) used for melting ice. Advanced corrosion could weaken the screws, leading to potential breakage during manoeuvring or parking. If all fixing screws fail, the power-assisted steering could detach, resulting in a loss of power steering and an increased risk of an accident.
Complaint Customer concern of Air Conditioning not cooling. *NOTE Use of tracer DYE for leak checks is not approved. Only approved leak check procedures as per WIS are approved. Cause Possible refrigerant leak. Remedy Perform the following measures : *Important* Photo documentation requirement is no longer in effect as of 10/1/2025. Remedy 1: Replace Evaporator (Only applies to vehicles produced PRIOR to April 15, 2022 and has NOT had the evaporator replaced previously) 1. Ensure that the rest of the AC system has been thoroughly checked for leaks with forming gas as per WIS before condemning the evaporator. 2. If no other leaks are found, replace the evaporator 3. *Important* when you get the new evaporator, check the expansion valve bracket to see if there are any bends (see attachment "Bent Bracket"). a. If bent, remove the expansion valve and bracket and check for damage to the flange (see attachment "Flange Damage"). i. If damage is found, order another evaporator and claim the part under parts warranty. The warranty claim MUST include a photo of the damage found. ii. If no damage is found, flip the bracket and torque to 7Nm. Check the evaporator for proper sealing before fully installing. b. If no bends are found, the evaporator should be installed in the vehicle. Note *If the evaporator housing has been opened or the evaporator or housing has been tampered with, the claim will be debited. Remedy 2: (Applies to all vehicles produced on or AFTER April 15, 2022 up to August 1, 2025) 1. Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . 2. If no leaks were found AND the system came in with no cooling/low charge, OR the evaporator is suspected of leaking: 3. Replace ONLY the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00, in accordance with the procedure outlined in WIS document AR83.30P5520ME. 4. IF THE PRODUCTION DATE IS BETWEEN JUNE 1, 2023 AND JULY 1, 2024, REPLACE THE DRYER AS WELL. (NOT THE CONDENSER) 5. After, charge the system and perform a few drive cycles. 6. Recheck the vehicle for leaks. 7. If no leaks are found, the vehicle can be released. 8. If a minor leak is detected that is less than 50ppm, then perform the following steps: If a leak is detected, fill the system with forming gas Close all doors and windows for 10 minutes. Vehicle off with no blower activation. Open the driver's door and measure ppm detection as soon as the door is open and the sniffer goes into the vehicle. If no leaks are measured, fill the system and release. If you still feel the evaporator is needed/leaks are still detected, a TIPS case is required for replacement. Provide all documentation listed in Remedy 3. Remedy 3: (Only applies to vehicles produced AFTER August 1, 2025) Ensure that the entire AC system has been thoroughly checked for leaks with forming gas as per WIS . If no leaks are found or the expansion valve has been found to be leaking, remove the expansion valve and check the bracket. If the bracket is bent, replace the expansion valve bracket, seals, and bolts as supplied in kit A 167 832 47 00. In the warranty submission, include photos of both sides of the bracket and a side profile so it can be seen that the bracket is bent. If the bracket is NOT bent or leaks from other locations are found, then open a TIPS case with the following: 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 4. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel if the evaporator is suspected. (see attached videos) 5. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks
Denuncia Rumore metallico proveniente dalla zona degli altoparlanti nelle portiere. Causa In fase di analisi. Rimedio Per restringere la causa, rimuovere innanzitutto il rivestimento della portiera. Se il rumore continua a verificarsi anche con il rivestimento della portiera rimosso, proseguire la diagnosi concentrandosi sull'altoparlante e, se necessario, aprire un caso TIPS con un video informativo come allegato. Nota: fare riferimento a questo documento nella richiesta di garanzia e, una volta completata la diagnosi, selezionare il codice di danno in base al componente che causa il problema. Se il rumore si interrompe quando il rivestimento della portiera viene rimosso, procedere in conformità con LI72.10P067691. Informazioni In questo caso, non utilizzare un codice di danno per gli altoparlanti nella richiesta di garanzia!
Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).