Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Nissan Juke

2010– · 3 generazioni · 19 difetti documentati · 5 mercati
Generazioni
Anno modello
Juke I · 2010–2019
RichiamoCriticoMotoreEU

An internal ignition switch may be defective

An internal ignition switch may be defective. As a consequence, the engine could unexpectedly stall while driving and under certain conditions the vehicle's airbag system may not function.

Safety Gate · UE29 ago 2018A12/1281/18Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.

Transport Canada8 mar 20182018121Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.

NHTSA · Stati Uniti7 mar 201818V156000Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreEU

Motorrijtuigen - krachtoverbrenging

Brandstofdruksensor niet correct vastgezet. Hierdoor kan de sensor onder invloed van warmte en trillingen losraken.

rdw23 mar 2015MGP150107Anni modello 2012–2013Mostrato in olandese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.

Transport Canada28 nov 20142014539Anni modello 2011–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.

NHTSA · Stati Uniti28 nov 201414V683000Anni modello 2012–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreJP

その他(燃料装置)

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不適切なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

MLIT · Giappone27 nov 20141134761Anni modello 2010–2014Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
Juke I · 2010–2019
RichiamoCriticoMotoreUK

Fuel may leak

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

DVSA · Regno Unito3 apr 2012R/2012/024Anni modello 2010–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan is recalling certain model year 2011-2012 juke, infiniti qx and infiniti m vehicles. The fuel pressure sensors may not have been tightened to the correct specification. As a result, the fuel pressure sensor may loosen due to heat and vibration causing fuel to leak.

NHTSA · Stati Uniti24 feb 201212V069000Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.

Transport Canada23 feb 20122012074Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
RichiamoModeratoMotoreUK

Engine push start switch may malfunction

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

DVSA · Regno Unito4 ago 2015R/2015/133Anni modello 2013–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreEU

null The push engine start switch may remain in the pressed position and not return after switching the…

null The push engine start switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition, the emergency engine stop function may operate and cause the engine to stop unexpectedly.

Safety Gate · UE30 giu 2015A12/0850/15Anni modello 2013–2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreJP

始動装置

プッシュエンジンスタータスイッチを組み付けるイモビライザアンテナの成形条件が不適切なため、熱収縮により、当該プッシュエンジンスタータスイッチとの隙間が狭くなり、摺動抵抗が増加したものがある。そのため、そのまま使用を続けると、当該スイッチ操作時に押したまま戻らず、緊急停止操作と判定してエンジンを停止することがあり、最悪の場合、走行中にエンストするおそれがある。

MLIT · Giappone25 giu 20151135950Anni modello 2013–2014Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreJP

エンジン本体

エンジンのタイミングチェーンにおいて、プレートを連結するピンの耐久性が不足しているため、表面処理が摩耗するものがある。そのまま使用を続けると、プレートのピン挿入穴が摩耗してタイミングチェーン全長が伸び、チェーンガイドと干渉して異音が発生し、最悪の場合、タイミングチェーンが破損してエンストに至るおそれがある。

MLIT · Giappone25 giu 20151135940Anni modello 2010–2012Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreUK

Fuel may leak

On affected vehicles the fuel pressure sensor may not have been tightened to the correct specification. Heat and engine vibration may cause the sensor to loosen and in extreme cases allow fuel to leak.

DVSA · Regno Unito30 mar 2015R/2014/167Anni modello 2012–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
Juke I · 2010–2019
Juke I · 2010–2019
RichiamoModeratoMotoreUK

Engine may stall

The Turbocharger boost sensor bracket may separate from the air inlet tube. This means the boost pressure may be measured incorrectly and the engine warning lamp may be illuminated. During low-speed driving this could cause the engine to stall and not restart

DVSA · Regno Unito23 gen 2012R/2011/166Anni modello 2010–2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreNA

Engine

On certain vehicles, a weld at the boost sensor bracket may fail, allowing the bracket to separate from the air inlet tube. If this occurred, the engine would enter fail-safe driving mode, resulting in reduced motive power in which the vehicle could still be driven for short distances. Continued operation could cause the engine to stall which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the air inlet tube assembly.

Transport Canada12 dic 20112011431Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoMotoreNA

Engine and engine cooling:Engine:Gasoline:Turbo/supercharger

Nissan is recalling certain model year 2011 nissan juke vehicles manufactured from april 9, 2010, through may 12, 2011. The turbocharger boost sensor bracket may separate from the air inlet tube due to a defective weld.

NHTSA · Stati Uniti8 dic 201111V583000Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).