Lettura libera · account gratuito per contribuireErede di Anticars (2000)

Nissan Juke

2010– · 3 generazioni · 19 difetti documentati · 5 mercati
Generazioni
Anno modello
Juke I · 2010–2019
RichiamoCriticoAbitacoloEU

En raison d’une erreur dans le processus de pliage du coussin gonflable du conducteur, le bouclier…

En raison d’une erreur dans le processus de pliage du coussin gonflable du conducteur, le bouclier thermique peut ne pas se déplacer complètement autour du gonfleur lorsque l’airbag est activé. par conséquent, le gaz chaud peut directement entrer en contact avec le panneau avant de l’airbag, causant des dommages de brûlure au matériau du sac. en conséquence, l’airbag peut se déchirer pendant l’inflation réduisant sa fonction protectrice.

Safety Gate · UE · RappelConso · Francia26 mar 2021a12/00391/21Anni modello 2019Mostrato in francese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoAbitacoloJP

始動装置

イグニッションスイッチのポジション保持用スプリングにおいて、成形設備のメンテナンスが不適切なため、成形時に傷がついたものがある。そのため、イグニッションキー操作の繰り返しによって当該スプリングが破損し、イグニッションキーに多数のキーホルダー等の重量物を装着していると、走行中の振動等によりイグニッションキーがON位置以外に回転し、車両電源が断たれてエンジンが停止するおそれがある。なお、この状態で事故を起こした場合、エアバッグが展開しない。

MLIT · Giappone6 set 20181143180Anni modello 2016–2018Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreEU

An internal ignition switch may be defective

An internal ignition switch may be defective. As a consequence, the engine could unexpectedly stall while driving and under certain conditions the vehicle's airbag system may not function.

Safety Gate · UE29 ago 2018A12/1281/18Anni modello 2017Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.

Transport Canada8 mar 20182018121Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.

NHTSA · Stati Uniti7 mar 201818V156000Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoFreniJP

圧力制御伝達部

ブレーキマスターシリンダにおいて、倍力装置内部のスプリングの製造のバラツキを考慮した設計をしていなかったため、ピストンが傾いて押されカップシールとの摺動抵抗が高くなり、ブレーキペダルを速く踏みこんだ際にカップシールが捲れることがある。そのため、シール部から倍力装置内部にブレーキ液が漏れ、そのままの状態で使用を続けると警告灯が点灯し、最悪の場合、制動力が低下して制動距離が長くなるおそれがある。

MLIT · Giappone1 feb 20181141890Anni modello 2015–2017Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoElettronicaNA

Electrical

On certain vehicles, due to a manufacturing defect the start/stop button could stick inside of its housing. If this occurs, vibration could cause the electrical components inside the button to contact repeatedly in quick succession and initiate the emergency engine shut off procedure while the vehicle is in motion. This could result in increased steering and braking effort, a loss of motive power and would disable the supplemental restraint systems (SRS), increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair defective start/stop switch as necessary.

Transport Canada25 giu 20152015282Anni modello 2013–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreEU

Motorrijtuigen - krachtoverbrenging

Brandstofdruksensor niet correct vastgezet. Hierdoor kan de sensor onder invloed van warmte en trillingen losraken.

rdw23 mar 2015MGP150107Anni modello 2012–2013Mostrato in olandese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoElettronicaEU

null The fuel rail pressure sensor of some vehicles may be tightened insufficiently to the fuel rail of…

null The fuel rail pressure sensor of some vehicles may be tightened insufficiently to the fuel rail of the engine and it may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition, in an extreme case, fuel leakage may occur between the fuel rail pressure sensor and the fuel rail.

Safety Gate · UE5 dic 2014A12/1975/14Anni modello 2012–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.

Transport Canada28 nov 20142014539Anni modello 2011–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.

NHTSA · Stati Uniti28 nov 201414V683000Anni modello 2012–2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreJP

その他(燃料装置)

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不適切なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

MLIT · Giappone27 nov 20141134761Anni modello 2010–2014Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
Juke I · 2010–2019
RichiamoCriticoAbitacoloUK

Airbag may release high temperature gases

In the event that the driver airbag is deployed during a frontal impact small holes may occur on the surface of the airbag. The holes are caused by high temperature gases from the airbag inflator exhausting directly onto the surface of the airbag material. The high temperature gas/airbag material may contact the drivers skin. The deployment performance of the driver airbag is not affected.

DVSA · Regno Unito25 feb 2013R/2013/019Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoAbitacoloEU

null In the event that the driver's airbag is deployed during a frontal impact, small holes may appear on…

null In the event that the driver's airbag is deployed during a frontal impact, small holes may appear on the surface of the airbag. The holes are caused by high temperature gas from the airbag inflator exhausting directly onto the surface of the airbag material. Contact of the high temperature gas / airbag material with the driver’s skin can cause burns.

Safety Gate · UE20 feb 2013A12/0243/13Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreUK

Fuel may leak

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

DVSA · Regno Unito3 apr 2012R/2012/024Anni modello 2010–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel system, gasoline

Nissan is recalling certain model year 2011-2012 juke, infiniti qx and infiniti m vehicles. The fuel pressure sensors may not have been tightened to the correct specification. As a result, the fuel pressure sensor may loosen due to heat and vibration causing fuel to leak.

NHTSA · Stati Uniti24 feb 201212V069000Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoElettronicaJP

コモンレール

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不充分なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

MLIT · Giappone23 feb 20121128970Anni modello 2010–2011Mostrato in giapponese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019
RichiamoCriticoMotoreNA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.

Transport Canada23 feb 20122012074Anni modello 2011–2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke II · 2019–
RichiamoModeratoAbitacoloUK

Juke (F16) Cintura di sicurezza anteriore

Sui veicoli interessati, la cintura di sicurezza anteriore potrebbe essere stata danneggiata accidentalmente durante la preparazione dei componenti per il montaggio.

DVSA · Regno Unito7 apr 2025R/2025/118Anni modello 2024Tradotto automaticamente · originale: ingleseVedi dettagli →
Juke I · 2010–2019Juke II · 2019–
RichiamoModeratoAltroUK

Juke (F16) Qashqai (J12) e Leaf (ZE1) VIN Scan

Sui veicoli interessati, il numero VIN memorizzato nel sistema del veicolo potrebbe non corrispondere al numero VIN effettivo del veicolo. Ciò può portare a una situazione in cui l'utente del veicolo visualizza informazioni relative a un altro veicolo, con conseguente violazione della sicurezza dei dati.

DVSA · Regno Unito17 giu 2024R/2024/234Anni modello 2019–2023Tradotto automaticamente · originale: ingleseVedi dettagli →
Juke I · 2010–2019
RichiamoModeratoFreniEU

En raison d’un changement de conception introduisant un chanfrein interne dans le bouton de verrouillage…

En raison d’un changement de conception introduisant un chanfrein interne dans le bouton de verrouillage arrière du siège arrière, la tige d’actionnement de la serrure peut attraper ce chanfrein, empêchant son mouvement vers le haut. en conséquence, le dossier du siège arrière peut ne pas être solidement verrouillé lorsqu’il est retourné à sa position verticale après pliage, et l’occupant du siège arrière et de tous les objets entreposés dans le compartiment à bagages peut ne pas être correctement retenu en cas d’accident, ce qui augmente le risque de blessure.

Safety Gate · UE · RappelConso · Francia8 ago 2023a12/01430/21Anni modello 2019–2020Mostrato in francese originale · traduzione in attesaVedi dettagli →
Juke II · 2019–
RichiamoModeratoFreniUK

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

DVSA · Regno Unito19 apr 2023R/2023/096Anni modello 2022Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Juke II · 2019–
RichiamoModeratoFreniEU

Si l’accélérateur et les pédales de frein sont pressés simultanément, cela provoque une réinitialisation…

Si l’accélérateur et les pédales de frein sont pressés simultanément, cela provoque une réinitialisation de la commande de véhicule électrique hybride (hevc). cela peut conduire à ce que le moteur trébuche ou décroche dans des conditions de conduite spécifiques (lorsque le moteur est froid, immédiatement après le démarrage), ce qui crée un risque d’accident.

Safety Gate · UE · RappelConso · Francia14 apr 2023a12/00724/23Anni modello 2022Mostrato in francese originale · traduzione in attesaVedi dettagli →
Juke I · 2010–2019Juke II · 2019–
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).