冷却装置
冷却ファンの制御基板に不良品が組み付けられているため、冷却水温が上昇しても、冷却ファンのモーターに電流が流れず、冷却ファンが作動しないことがある。そのため、そのまま使用を続けると、エンジンがオーバーヒートする。又は、制御基板が発熱し、最悪の場合、火災に至るおそれがある。
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Peugeot 407 (tutte le generazioni)
冷却ファンの制御基板に不良品が組み付けられているため、冷却水温が上昇しても、冷却ファンのモーターに電流が流れず、冷却ファンが作動しないことがある。そのため、そのまま使用を続けると、エンジンがオーバーヒートする。又は、制御基板が発熱し、最悪の場合、火災に至るおそれがある。
È stato accertato che, sui veicoli interessati, può manifestarsi un guasto alla pompa del vuoto del servofreno. Ciò può causare l'indurimento del pedale del freno con conseguente perdita di efficacia della frenata.
There is a possibility of a non conformity of the engine cooling motor fan unit which can result in a failure of the unit or exceptionally in local overheating that can result in combustion of the unit.
冷却ファンの制御基盤に不良品が組み付けられているため、冷却水温が上昇しても、冷却ファンのモーターに電流が流れず、冷却ファンが作動しないことがある。そのため、そのまま使用を続けると、エンジンがオーバーヒートする、又は、制御基盤が発熱し、最悪の場合、火災に至るおそれがある。
On subject vehicles the fitting of the diesel high pressure delivery pipe may be constricted. Should this be the case a fuel leak may occur.
It has been identified that on certain vehicles a fault may be present on the diesel fuel circuit return pipe at the location of the pressure sensor.In the manufacture of the pipe an excess of material resulted in a reduction of the pipe's internal diameter therefore restricting the fuel flow and a risk of a diesel leak from the fuel connector.
Due to a potential fault in the engine management system an internal engine fuel leak via the injectors may occur following switching off. This would result in the engine failing to restart due to excess fuel being present in the inlet manifold or cylinders.
It is possible for the engine to stall due to incorrect reading of oil levels during harsh and prolonged braking.
駐車ブレーキレバーのワイヤー自動巻き取り調整機構の製造工程において、不適切な固定加工を行ったため、当該部品が変形し、ワイヤー自動巻き取り調整機構が作動しなくなるものがある。そのため、繰返しの駐車ブレーキレバー操作によりワイヤーの伸び代が過大になり、車両の駐車制動力が不足するおそれがある。
In very rare circumstances the vacuum pump one way valve may not function correctly which could affect the level of braking assistance.
The parking brake may fail to hold the vehicle stationary when applied. If this defect occurs the driver will be alerted by a weak effort when moving the parking brake lever.
制動灯スイッチ内部の接点の電気負荷に対する容量が不足しているため、ブレーキの繰り返し操作により接点が消耗し、制動灯が点灯しなくなり、シフトレバーがパーキング位置から動かなくなる、または再始動できないおそれがある。
엔진과 브레이크 압력증가 장치 사이에 연결된 진공 브레이크 파이프에 엔진오일이 들어갈 가능성이 있고, 엔진오일이 들어간 상태로 오랜 시간 동안 사용할 경우 브레이크 능력이 떨어질 가능성이 있는 결함('08년 동일 현상 F리콜대상인 607HDI 차량 409대 포함)
Residual low pressure persists in the power braking vacuum circuit which may result in the loss of power assistance when braking
It has been identified that a slight amount of play in the diesel fuel return pipe mountings on certain vehicles may over time lead to abrasion and wear of the pipe.
It has been identified that the main engine fuse box is not to the correct specification. This can result in operating faults or the failure of certain equipment.
A deterioration of the brake assistance may occur because it is possible for the brake servo valve to leak oil which can damage the membrane of the brake servo.
It is possible that the engine may stall when lifting your foot off of the accelerator immediately after high speed usage of the vehicle.
There is a possibility of untimely triggering of the starter motor which if the vehicle has been left in gear could result in the vehicle jerking forward when the starter motor engages.
There is a risk of a manufacturing non conformity on the fuel injection diesel return pipe. This may lead to the possibility of fuel seepage.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).