1,610 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 1991–1995), typically at around 80,000 miles. Most often named: engine (62%), engine:gasoline (23%). Reported consequences: 9 crashes, 60 fires, 12 injuries, 1 death.
446 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1991–1995), typically at around 120,000 miles. Most often named: ignition (33%), ignition:switch (15%). Reported consequences: 3 crashes, 76 fires, 14 injuries, 1 death.
278 owners in the United States reported problems with the accelerator and cruise control of this car to NHTSA (model years 1991–1995), typically at around 89,000 miles. Reported consequences: 33 crashes, 6 fires, 18 injuries, 1 death.
340 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 1986–1990), typically at around 79,000 miles. Most often named: ignition:switch (48%), ignition (24%). Reported consequences: 1 crash, 115 fires, 2 injuries.
304 owners in the United States reported problems with the engine and cooling of this car to NHTSA (model years 1986–1990), typically at around 67,000 miles. Most often named: engine (47%), engine:gasoline (39%). Reported consequences: 4 crashes, 43 fires, 7 injuries.
Ford Motor Company (Ford) is recalling certain 2015-2019 Flex, 2015 Explorer, Lincoln MKT, Lincoln MKZ, 2015-2016 C-Max, Escape, Taurus, 2016 Fusion, 2018-2019 Taurus, 2019 Lincoln MKT, Fiesta, and 2020 Mustang vehicles. The rearview camera may display a distorted, intermittent, or blank image when the vehicle is in reverse.
Ford Motor Company (Ford) is recalling certain 2014-2016 Explorer, 2014-2015 Taurus and 2014 Edge vehicles equipped with 2.0L or 2.3L engines and front wheel drive. The support bracket for the front drive axle halfshaft may fail.
Advance Notice Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
Some 2015-2016 vehicles equipped with 6F50/6F55 transmission and built on 2-Nov-2015 and through 1-Feb-2016 may exhibit no reverse, 3rd and 5th gear with diagnostic trouble codes (DTCs) P0715,P0717,P0756 and/or P2701. This may be caused by the direct clutch cylinder/tone wheel (7F283) inadvertently forcing the snap ring out of position resulting in damage to the direct clutch hub (7G384). Service part (7J250) complete rotating 3-5-R clutch module is now available. Refer to Workshop Manual (WSM), Section 307-01. For claiming, use causal part 7F283 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) manual.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)。