閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

GMCGMC エンボイ

1998–2009 · 2 世代 · 不具合27件 · 1市場
世代

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

年式
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

この予備情報通報は、セキュリティライトが点灯した状態で、断続的にクランクしない、始動しない、または始動時にエンストするという症状が発生している車両について、整備技術者に情報を提供するものです。整備技術者は診断トラブルコード B3055、B3

NHTSA · メーカー通報11039894モデルイヤー 2007自動翻訳 · 原文:英語詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

この技術情報(Preliminary Information)は、セキュリティライトが点灯し、断続的にクランキングしない、始動しない、または始動後にストールするという症状が見られる車両について、技術者に情報を提供するものです。技術者は、診断トラブルコード B3055、B3060、B3935、C0750、C0755、C0760、C0765、および/または C0775 を確認する場合があります。

NHTSA · メーカー通報11021792モデルイヤー 2007自動翻訳 · 原文:英語詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · メーカー通報10232136モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

NHTSA · メーカー通報10219266モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · メーカー通報10200151モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · メーカー通報10114954モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

NHTSA · メーカー通報10114746モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · メーカー通報10114354モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

10054E - Special Coverage (customer co-pay discontinued). The contacts on the fuel level sensor may wear prematurely. This wear could cause the fuel gauge to read empty after filling the tank and cause the malfunction indicator light (MIL) to illuminate. As the fuel level in the tank drops, the MIL may turn off and the gauge may display a reading; however, the reading may indicate a slightly higher level of fuel than what is in the tank. Eventually, as the contacts continue to wear, the fuel gauge will stop working and the MIL will illuminate continuously. If the condition occurs within the stated terms, dealers will install a new design fuel level sensor.

NHTSA · メーカー通報10114183モデルイヤー 2005–2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

NHTSA · メーカー通報10113418モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · メーカー通報10113177モデルイヤー 2004原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · メーカー通報10113120モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · メーカー通報10112697モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · メーカー通報10112436モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · メーカー通報10111927モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · メーカー通報10111737モデルイヤー 2004原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

Diagnostic information on engine oil leak from rear of crankshaft. *tt 05-06-01*022 supplement - crankshaft oil leak repair instrumentions. *tt

NHTSA · メーカー通報10017385モデルイヤー 2005原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

Service engine soon light due a diagnostic trouble code p0606 diagnostic trouble code, operate in reduced engine power mode, and potentially stall. *tt

NHTSA · メーカー通報10017230モデルイヤー 2004原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報中程度電装NA

技術通報

Concerns with no start, turn/hazard, interior lamps, driver information center (dic), radio, theft alarm, wipers, cruise, shift interlock, horn and/or key in signal inoperative. *tt

NHTSA · メーカー通報628833モデルイヤー 2002原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

この技術サービス情報(サービスブレティン)は、冷間放置(コールドソーク)後の始動時に、パーキング(P)に入れた状態で一部の車両が前後にわずかに揺れる、または動く場合があることについて説明するものです。この症状にはガタンという異音が伴うことがあります。動きはわずかで、体感するよりも、外から見て目視で確認されることが多いものです。また、装備されている場合はオートスタート機能を使用したときに発生します。

NHTSA · メーカー通報11009088モデルイヤー 2007自動翻訳 · 原文:英語詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

Vehicle Wide Programming(VWP)は、GM車両のソフトウェアを更新するための新しいプロセスです。Techline Connect内で1回の選択を行うだけで、まず更新が必要なモジュールを特定し、その後(一部の例外を除き)影響を受けるモジュールの更新を進めることができます。モジュールの更新は、整備士が1つずつ更新する必要なく、並行して完了します。これにより、ディーラーとお客様にとってより合理化された方法が実現します。

NHTSA · メーカー通報11006621モデルイヤー 2006自動翻訳 · 原文:英語詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

この技術広報では、導電性仕上げを施した新しいゼネラルモーターズ(GM)純正交換用ファスナーを使用した電気アース修理に関する情報を提供します。

NHTSA · メーカー通報10252735モデルイヤー 2006自動翻訳 · 原文:英語詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

NHTSA · メーカー通報10249011モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

Programming And Activation Of Replacement OnStar Modules.

NHTSA · メーカー通報10246951モデルイヤー 2006原文(英語)で表示中 · 翻訳待ち詳細を見る →
エンボイ II · 2002–2009
技術通報軽微電装NA

技術通報

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · メーカー通報10237387モデルイヤー 2007原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。