This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. 01-007/24 06/20/24 ENGINE OIL LEVEL WARNING LIGHT ON WITH DTC P250F:00 DUE TO LOW ENGINE OIL LEVEL (UPDATED WITH SSPD5 INFORMATION). All Mazda Dealers: Follow the Special Service Program SSPD5 Valve Stem Seal Class Action for determination if valve stem seals should be replaced. 1. Verify the customer concern following the Special Service Program SSPD5 Repair Procedure. As the repair procedure states in SSPD5, confirm the engine oil is not leaking from the engine. If the customer reports engine oil is low upon arrival at a dealer, replace the valve stem seals following the flow chart for SSPD5. If engine oil is low upon arrival with no customer complaint, check for SSPD5 and if the valve stem seals have not been replaced under prior Warranty, replace the seals. If the valve stem seals have been replaced under a prior Warranty claim, contact Hotline for further instructions. If valve stem seals need to be replaced, replace the valve seals of the exhaust side with improved ones using the special tools called out in the repair procedures below. 2. Top off the engine oil (if needed). NOTE: Engine oil should not be topped off without replacement of the valve stem seals. 3. Verify the repair. NOTE: If unsure what steps to take during a customer visit for oil consumption related to SSPD5, fill out Dealer Recall Help on OneMazda.
Some vehicles may have a "LOW ENGINE OIL LEVEL" warning message and an engine oil level warning light on in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the design of these valve seals has been modified.
Some customer may experience the wireless charger does not start charging or stops charging immediately although the mobile device is in the chargeable area. This is caused by the logic for detecting foreign matter being too sensitive.
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built March 20, 2021 and later.
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
Connected vehicle remote functions inoperative and/or engine no start due to low battery voltage. Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later.
Some customers may experience the following symptoms: Connected Vehicle Remote Functions inoperative after SSPC6 repair. Connected Vehicle Remote Functions inoperative on vehicles built July 1, 2021 and later. Engine no start due to low battery voltage.
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019 Mazda3 is not equipped with factory installed navigation system, however, it is available as a dealer installed accessory. SiriusXM Traffic Plus and Travel Link are available on the 2019 Mazda3 Preferred Package and above, as a paid subscription. Traffic Plus feature requires in-vehicle navigation SD card. SiriusXM Satellite Radio trial subscription is free of charge for 3 months.
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by an internal FSC failure. To eliminate this concern, the production process of the FSC has been modified.
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc.This only occurs with MAZDA CONNECT software version 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.504.
This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
Some customers may experience the following symptoms: No sound from some audio sources (AM, FM, SiriusXM) after turning the ignition on. Radio station selection (AM, FM, SiriusXM) changes unintentionally after turning the ignition on. Audio source cannot be changed. Diagnosing according to MGSS online does not solve the problem. These concerns may be caused by the remote tuner not operating properly under certain situations. To eliminate these concerns, the remote tuner control software has been modified.
Some customers may complain about any of the following: Infotainment display is blank Rear mount camera is inoperative Foot-motion system is inoperative Rear parking sensor system is inoperative Battery is discharged INTERIOR2 15amp fuse is blown
SPECIAL SERVICE PROGRAM SSPC8 - 2023 CX-9, 2023 MAZDA3, 2022-2023 MX-30 - REMOTE TUNER CONCERN. Mazda Motor Corporation has decided to conduct a Special Service Program on certain 2023 CX-9, 2023 Mazda3 and 2022-2023 MX-30 vehicles equipped with a Remote Tuner module. There are 16,405 U.S. vehicles in the United States affected by this SSP.Certain Remote Tuner modules were built with outdated software and therefore the power shutdown processing of the module may not be completed. In this condition, if the vehicle is left unused for a certain amount of time, the 12V battery may discharge and run out.
Some vehicles may have a "LOW ENGINE OIL LEVEL" warning message and a CHECK ENGINE light illuminated in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the design of these valve seals has been modified.
Some vehicles may have a "OW ENGINE OIL LEVEL" warning message and a CHECK ENGINE light illuminated in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. * DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the design of these valve seals has been modified.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。