Certain vehicles may have been assembled with faulty seat track assemblies. Specifically, the driver's inboard, and the passenger's outboard seat tracks, may have undersized slots in two locations. This may result in the manual seat pawl not fully engaging in those slots. Should the vehicle be involved in a crash, occupants of front seats with affected seat tracks would be exposed to an increased risk of personal injury or death. Correction: Dealers will inspect and, if necessary, replace the entire seat assembly.
On certain vehicles, the 3rd-row curtain side-impact airbag on the driver's side may have been installed slightly out of position during vehicle assembly. This could cause the airbag to inflate in a manner different than designed or not inflate at all. The most likely result of this mis-installation is a delayed deployment. Nissan testing has determined that the delay would be about 20 msc compared with the design intent, and the bag will still be inflated before a 3rd-row occupant might interact with it in a side impact crash. Testing also determined that in the event of a non-deployment, the vehicle still exceeds all safety requirements in the third row seats. Correction: Dealers will inspect and, if required, reposition the 3rd-row curtain side-impact airbag. This action is deemed a voluntary service campaign and is not being conducted under the Motor Vehicel Safety Act.
On vehicles equipped with the automatic airbag suppression feature option, the front passenger seat is equipped with a seat cushion bladder and sensors used for occupant detection. When a certain child dummy is placed in the required positions for US Government tests, automatic suppression may not occur. Correction: Dealers will inspect the front passenger seat cushion/sensor assembly. If the seat cushion/sensor is found to be operating improperly, the seat will be removed and recalibrated. Nissan in the United States is conducting this safety recall campaign to correct an out of compliance condition with US regulations. While there are approximately 1,524 vehicles in Canada affected by this condition, Canadian regulations in this area differ from those in the United States and thus Canadian vehicles are not out of compliance. However, in the interest of customer satisfaction, Nissan Canada Inc., will be conducting a Voluntary Customer Satisfaction Initiative to have owners of affected Canadian vehicles return to their dealers for inspection and recalibration if required.
Certain vehicles do not comply with the requirements of CMVSS 209 - Seat Belt Assemblies. The seat belt assemblies may not withstand the force requirements of the standard. In a crash, if the belt buckle fails, there is an increased risk of injury to the occupant. Correction: Belt buckle assemblies will be inspected and replaced if necessary.
On certain vehicles, the seat belt assemblies may not withstand the force requirements of the standard. In a crash, if the belt buckle fails, there is an increased risk of injury to the occupant. Correction: Dealer will replace the seat belt buckle assembly.
Nissan North America, Inc. (Nissan) は、2008~2011年式の Titan、Frontier、Xterra、Pathfinder、Armada、および2008~2009年式の Quest の一部車両をリコールしています。運転席エアバッグカバーの樹脂製エンブレムに亀裂が入り、エアバッグ展開時に剥がれるおそれがあります。
Nissan is recalling 1,126 my 2008 quest, titan and armada vehicles equipped with manual adjustment front seats. These vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 207, "seating systems." the seat track assembly may have been manufactured out of specification.
On certain mini vans equipped with a folding third row rear seat, when the third row seat is raised from its stowed position, it engages striker brackets, one on each side of the seat cushion. The fold-away striker loop is welded to a mounting bracket. The striker may become detached from its mounting bracket due to a broken weld at the point of attachment to the bracket.
On certain mini vans, there is a seat adjustment mechanism that contains exposed moving components located at the rear inside edge of the second row seat.
On certain vehicles, a third row seat bracket striker may become detached from its mounting bracket due to a broken weld at the point of attachment. Striker separation may increase the risk of injury to seat occupants in certain types of collisions. Correction: The third row seat striker brackets will be replaced.
On certain vehicles, the seat adjustment mechanism contains exposed moving metal components located at the rear inside edge of the second row seat. An operators finger may be pinched in the mechanism during seat adjustment. Correction: Dealers will install a plastic reinforcement to the backside of the existing seat back cover carpeting.
Certain passenger vehicles fail to comply with the advanced air bag requirements of federal motor vehicle safety standard no. 208, "occupant crash protection." the air bag for the front passenger seat is to be turned off (so that it does not inflate) when certain occupants, such as small children, are in the front seat.
Vehicle description: Passenger vehicles equipped with trw seat belt buckle assemblies. The buckle base of these seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of federal motor vehicle safety standard no. 209, "seat belt assemblies."
On certain vehicles, the easy entry and exit latch system on the second row right hand side captain's chair may have inadequate lubrication. In some cases the actuator spring may deform after repeated use, causing the latch to remain in the unlatched position. If this occurs, the seat will slide freely on the seat track and the springs on the track will move the seat to the easy entry position toward the front of the vehicle. An unlatched seat track could result in an increased risk of injury in the event of a crash. Correction: Vehicles will be inspected and latches will be lubricated or replaced as necessary.
Vehicle description: Mini vans equipped with e-z entry seats. The affected vehicles may have a second row right hand side captain chair that has inadequate lubrication of the easy entry and exit latch system. In some cases, the actuator spring in the latch could deform after repeated use, causing the latch to remain in the unlatched position. If this occurs, the seat will slide freely on the seat track and the springs on the track will move the seat to the easy entry position toward the front of the vehicle.
Note: All vehicles involved in this recall were corrected prior to final delivery. These vehicles may not comply with c.M.V.S.S. 207 - anchorage of seats and 210 - seat belt assembly anchorages. Certain seat belt anchorages are attached to the third seat. The sliding seat latch on the this seat may not fully engage and therefore the seat may not sustain the loads specified in the standards. Correction: The seat guide rollers will be inspected and replaced if required.
An out-of-specification condition in the seat cable roller pulley assembly can allow the cable that connects the seat adjust lever to the latch to be pinched in the roller assembly.
Vehicle description: Mini vans. These vehicles may have the plastic trim cover around the base of the front seat safety belt buckle trapped between the shoulder of the restraint anchorage bolt and the seat pedestal. This could eventually allow the seat belt buckle bolt to loosen.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。