무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

BMW 7 시리즈 E38

1994–2001 · 결함 9건 · 3개 시장
연식
리콜심각서스펜션JP

かじ取ギヤボックス

かじ取り装置において、ギアボックスにある油圧パイプの取り付けボルトの締め付けトル クが不適切なため、走行時の振動等で当該ボルトがゆるむものがあり、そのままの状態で 使用を続けると、パワーステアリングの作動油が漏れてかじ取りハンドルの操舵力が増大 し、最悪の場合、漏れた作動油が着火して火災に至るおそれがある。

국토교통성 · 일본2003년 3월 11일1210100연식 2000원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각변속기NA

Power train:Driveline:Differential unit

Vehicle description: Passenger vehicles. The differential pinion shaft within the differential case assembly was produced without the appropriate surface hardening. This can result in the shaft experiencing premature wear.

NHTSA · 미국1998년 6월 22일98V142000연식 1998원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션JP

スプリング/エアサス

緩衝装置において、前輪側のコイルスプリングの形状が不適切なため、そのままの状態で 主に積雪地帯での使用をすると、当該スプリングと下部のパッドとの間に蓄積された異物 により生じた傷から腐食することがあり、最悪の場合、折損し、走行安定性を損なうおそ れがある。

국토교통성 · 일본2001년 9월 27일1209040연식 1994–1996원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통전장NA

Electrical

On certain 323I, 328I, 528I, 528IT, 540I, 540IT, 740I, 740IL, 750IL and M5 vehicles, the brake light switch capacitor housing may be cracked and in high humidity conditions the capacitor and switch housing could become overheated and deformed. As a result, a short circuit or an open circuit could occur in the switch. This could cause the switch to remain either in the "brake lamps off" position or the "brake lamps on" position. If the switch remains in the "off" position, the brake lamps will be rendered inoperative. Conversely, if the switch remains in the "on" position, the brake lamps will be continuously illuminated when the ignition switch is in the "on" position. Correction: Brake lamp switch will be replaced with an improved switch.

캐나다 교통부2000년 3월 9일2000065연식 2000원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통브레이크JP

制動灯

制動灯の制御回路において、制動灯用スイッチに一部製造不良のものがあり、そのままの 状態で使用を続けると電子回路が故障し、最悪の場合、ブレーキペダルの操作とは関係な く、制動灯が点滅もしくは点灯し続けてしまうおそれがある。

국토교통성 · 일본2000년 2월 17일1207850연식 1999원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통브레이크NA

Exterior lighting:Brake lights:Switch

Vehicle description: Passenger vehicles. The brake lamps in these vehicles are controlled by a switch activated by the movement of the brake pedal. This switch could fail internally, causing it to remain either in the "brake lamps off" position or in the "brake lamps on" position.

NHTSA · 미국2000년 2월 17일00V048000연식 2000원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통브레이크UK

Brake lights may fail to operate remain on or flicker

There is a possibility that the brake light switch circuits may become defective and cause the brake light circuit to fail stay on continuously or flicker. In extreme cases the brake switch could overheat.

DVSA · 영국1999년 12월 15일R/1999/104연식 1999원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통전장NA

Electrical system:12v/24v/48v battery:Cables

Vehicle description: Passenger vehicles. The thickness of the main positive electrical cable (generator to starter) insulation is less than specified, making it susceptible to being abraded or cut by the clip that secures the cable to the generator.

NHTSA · 미국1999년 1월 4일99V004000연식 1999원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통변속기NA

Power train:Automatic transmission

Vehicle description: Passenger vehicles equipped with a 5hp24 automatic transmission. Premature wear of the ring gear can occur, leading to the loss of 1st, 2nd, 3rd, and reverse gears.

NHTSA · 미국1999년 1월 4일99V005000연식 1999원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통실내NA

Heater And Defroster

On certain vehicles, failure of a cooling system component such as thermostat, water pump or fan belt can result in a significant increase in coolant temperature and system pressure. Increased system pressure could result the formation of a crack or separation of a seam in the heater core end piece which would cause hot coolant to be expelled from the heater core. This hot fluid could contact car occupants resulting in possible personal injury and/or fogging of the interior window surfaces. Correction: Radiator cap will be replaced with a new design cap in order to avoid buildup of excessive pressure in the cooling system.

캐나다 교통부1998년 10월 14일1998197연식 1994–1995원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · 미국1998년 8월 4일98V178000연식 1994–1995원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통변속기NA

Powertrain

On certain 540I, 540IA, 740IA, 740ILA and 750ILA, the differential pinion shaft in the differential case assembly was not properly surface hardened. This condition will result in premature wear which can lead to noisy operation and ultimately to a lack of drive capability through the rear axle. Correction: Entire differential assembly will be replace on affected vehicles.

캐나다 교통부1998년 7월 15일1998134연식 1998원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션NA

Suspension

On certain 740I, 740IL and 750IL vehicles, road grit and gravel associated with winter road conditions can penetrate the rubber of the lower front spring mounts and accumulate in the mounts causing notches or pits to develop. Eventually this could cause the coild spring to crack and break at a bottom coild. This could adversely affect the vehicle's dynamic stability and reduce driver control. Correction: Both front springs and lower spring mounts will be replace on affected vehicles.

캐나다 교통부1997년 10월 9일1997174연식 1995–1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진NA

엔진

특정 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI, M3에서는 크루즈 컨트롤과 스로틀 케이블이 스로틀 하우징의 동일한 스로틀 밸브 작동 레버에 연결되어 있습니다. 어느 케이블의 플라스틱 부싱이 파손되어 외부 케이블 하우징이 부싱에서 분리될 수 있습니다. 크루즈 컨트롤 작동 없이 스로틀 페달을 적용하면 외부 튜브가 부러진 부싱 가장자리에 걸려 스로틀 밸브가 부분적으로 열린 상태로 유지될 수 있습니다. 이런 일이 발생하면 차량이 예상대로 감속하지 못해 충돌이 발생할 수 있습니다. 정정: 각 케이블의 외부 튜브에 스프링 클립이 설치되어 부싱에서 떨어지는 것을 방지합니다.

캐나다 교통부1997년 10월 9일1997173연식 1995–1997자동 번역 · 원문: 영어자세히 보기 →
리콜보통엔진NA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · 미국1997년 8월 19일97V131000연식 1994–1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통전장NA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

캐나다 교통부1996년 10월 7일1996158연식 1994원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통브레이크NA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · 미국1996년 7월 1일96V111000연식 1994원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통엔진JP

燃料ホース/パイプ

エンジンル-ム内の金属製燃料パイプの端部形状が不適切なため、車両の振動等により 当該パイプに接続するゴム製燃料ホースが損傷し、そのままの状態で使用を続けると燃料 が漏れるおそれがある。

국토교통성 · 일본1996년 2월 8일1205812연식 1994–1995원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션JP

その他(緩衝装置)

後輪右側の緩衝装置を構成するホイールキャリア(ホイール取付用部品)に鋳造不良の ものがあり、そのままの状態で使用を続けると、鋳造不良の部分が破損し、走行安定性を 損なうおそれがある。

국토교통성 · 일본1996년 2월 8일1205811연식 1995원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션NA

Suspension

On certain 740I, 740IL and 750IL vehicles, the lower suspension arm mounting eye on the right side rear axle hub carrier could have a casting flaw. It is possible that the carrier eye could crack and break during driving. If this were to occur, the right rear wheel would no longer function as designed and the driver's ability to maintain control of the vehicle would be considerably reduced. Correction: Right side rear axle hub carrier will be inspected for the presence of the casting flaw and replaced if the flaw is present.

캐나다 교통부1995년 10월 23일1995189연식 1995원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통서스펜션NA

Suspension:Rear

The lower suspension arm mounting eye on the right side rear axle hub carrier was produced with a casting flaw.

NHTSA · 미국1995년 10월 11일95V192000연식 1995원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜경미차체NA

장비: 기타: 라벨

미국 규격은 연방 자동차 안전 기준 111호인 "백미러"를 준수하지 않은 2002년식 포르쉐 카레라 1대, 1997년식 BMW 750IL 1대, 1986년형 BMW 635 CSI 차량 2대를 리콜합니다. 미국 시장을 위해 적합성 관련 개조를 수행하던 중, 조수석 사이드 미러에 잘못된 크기의 글꼴이 붙은 라벨이 부착되었습니다.

NHTSA · 미국2013년 2월 26일13V063000연식 1997자동 번역 · 원문: 영어자세히 보기 →
리콜경미서스펜션NA

Suspension:Front:Springs:Coil springs

Vehicle description: Passenger vehicles. Road grit and gravel associated with winter road conditions can penetrate the rubber of the lower front spring mounts and accumulate in the mounts causing notches or pits to develop. These notches can develop cracks resulting in breakage of a bottom coil of the spring.

NHTSA · 미국1997년 8월 22일97V140000연식 1995–1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).