BMW 부품 공지 TEC1T RDC 모듈 반품
BMW NA는 다음 부품 번호에 대한 점검을 요청했습니다: 36 10 6 856 227 및 36 10 6 798 872. 재고는 판매하거나 어떤 차량에도 설치해서는 안 됩니다. 해당 부품을 귀사의 담당 지역 유통센터(RDC)로 반품해 주십시오. 반품 신청은 주문 사유 BM2를 사용하여 YR26 손상 클레임으로 제출하십시오. 유효한 BMW 배송 번호와 배송 품목 번호를 입력해야 하며, TEC 클레임 본문에 TEC1T가 반드시 포함되어야 합니다. TEC1T는 2013년 5월 30일부터 2013년 6월 13일까지 유효합니다. TEC1T에 대한 클레임 제출 기한은 2013년 6월 13일입니다. 모든 부품은 늦어도 2013년 6월 27일까지 담당 RDC로 반품되어야 합니다.
부품 번호 36 10 6 856 227: 인덱스가 02 이하인 모든 부품은 반품해야 합니다. 인덱스가 03인 부품은 정상입니다.
부품 번호 36 10 6 798 872: 인덱스가 03 이하인 모든 부품은 반품해야 합니다. 인덱스가 04인 부품은 정상입니다.
인덱스는 박스 라벨의 바코드 아래에 있는 두 자리 코드입니다. 인덱스는 부품 자체의 부품 번호 바로 뒤에서도 확인할 수 있습니다.
필요한 경우 동일한 부품 번호로 다시 주문하십시오.
(c) 2013, BMW of North America, LLC. 이 문서의 내용은 기밀이며 제3자에게 배포 목적으로 공유해서는 안 됩니다.
CLOSED-CIRCUIT CURRENT MONITORING. Increased closed-circuit currents may occur permanently or intermittently and cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control module or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control module will be reset if the battery is disconnected. Following a reset, the faulty control module may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp or 100-amp clip-on probe can be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time.
NHTSA · 제조사 공지10149555원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
2013 MINI JCW Paddle Shifter Retrofit. SZL to EGS harness installation. For necessary preliminary tasks, refer to ISTA and perform the following steps listed in this document.
NHTSA · 제조사 공지10149498원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
N63: Proper Ignition Harness Installation and Ground Connections. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16511.1.B12241... 10/14/2014 Page 2 of 2 Any consecutive damage to the BSD interface components (DME, alternator voltage regulator, QLT sensor) caused by incorrect reinstallation of the ignition harness is not covered under the BMW New Vehicle /SAV Limited Warranty.
NHTSA · 제조사 공지10148021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a high-voltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use in accordance with their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging systems and a simplified tool and battery voltage checking procedure below.
NHTSA · 제조사 공지10148035원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
BMW Parts Bulletin TEC9V Fuel Tank / Level Sensor Returns BMW AG has requested an inspection of the following part numbers: 16 11 7 268 031, 16 11 7 268 032 and 16 11 7 297 340 Stock should not be sold or installed on any vehicle. 16 11 7 268 031 and 16 11 7 268 032 All fuel tanks produced before 05/30/2014 needs to be returned. All parts with later dates of production are ok and can be used. 16 11 7 297 340 All level sensors produced in Poland before 05/19/2014 (date is shown as day 139 of year 14 on the part) need to be returned. Those produced after this date are ok and can be used. All level sensors produced in Brazil currently in dealer inventory need to be returned. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC9V must appear in the text of your TEC claim. TEC9V is valid from September 24, 2014, through October 08, 2014. The deadline for filing a claim under TEC9V is October 08, 2014. All parts must be returned to your facing RDC no later than October 22, 2014. Please re-order the same part numbers as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution. Page 2 / 2 Made in Poland Made in Brazil Need to be returned (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.
NHTSA · 제조사 공지10148044원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
BMW Parts Bulletin TEC3W Leak Diagnosis Module Return BMW AG has requested a return of the following part numbers: 16 13 7 315 813 and 16 13 7 274 147 Stock should not be sold or installed on any vehicle. Leak Diagnosis Module part number 16 13 7 315 813 must be returned. Please reorder new part number 16 13 7 333 302 as needed. Pressure Switch, Leak Diagnosis Module part number 16 13 7 274 147 must also be returned. Please reorder new part number 16 13 7 333 301 as needed. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC3W must appear in the text of your TEC claim. TEC3W is valid from September 04, 2014, through September 18, 2014. The deadline for filing a claim under TEC3W is September 18, 2014. All parts must be returned to your facing RDC no later than October 02, 2014.
NHTSA · 제조사 공지10148045원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
BMW Parts Bulletin TEC1U RDC Module Return BMW AG has requested an inspection of the following part numbers: 36 10 6 798 872 and 36 10 6 856 227 Stock should not be sold or installed on any vehicle. All parts with a date of and from 26/07/13 (July 26, 2013) are good. All parts with a date prior to 26/7/13 (July 26, 2013) must be returned to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC1U must appear in the text of your TEC claim. TEC1U is valid from March 5, 2014, through March 19, 2014.The deadline for filing a claim under TEC1U is March 19, 2014. All parts must be returned to your facing RDC no later than April 2, 2014. Please re-order the same part number as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.
NHTSA · 제조사 공지10148013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
TEC9T Return, Battery AGM. BMW AG has requested an inspection and return of affected batteries with the following part number: 61 21 8 520 153: Battery AGM Please inspect your stock of this battery. Batteries with finish code label E3, F3, G3, H3, I3, J3 and K3 should not be sold or installed on any motorcycle and must be held for scrapping by your ACM or FSE.
NHTSA · 제조사 공지10147993원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Closed-circuit Current Measurement. Increased closed-circuit currents may occur permanently or intermittently, and may cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control unit, or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control unit will be reset if the battery is disconnected. Following a reset, the faulty control unit may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp clip-on probe (previously used with the IMIB) or the 100-amp clip-on probe can now be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time. Connect the amp clip-on probe directly to the IMIB Measurement input 3 (green socket).
NHTSA · 제조사 공지10147940원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
?Delivery Stop ? Natural Vacuum Leak Detection Temperature Sensor. A Delivery Stop has been issued on 6 Series Gran Coupe (F06), 5 Series Sedan (F10), 6 Series Convertible (F12), 6 Series Coupe (F13), and 7 Series (G12) vehicles produced from November 3, 2015 to November 5, 2015. These vehicles may have the incorrect Natural Vacuum Leak Detection (NVLD) temperature sensor installed. Please reference SI B16 09 15 (attached) for additional information. Please be reminded that it is a violation of Federal law for you to sell, lease or deliver any vehicle covered by this notification until the delivery stop repair has been performed. This means that centers may not legally deliver new motor vehicles to a consumer until it is fixed or use/sell replacement equipment/parts subject to a delivery stop. Note also that substantial civil penalties apply to violations of this law. Also, you should not sell, lease or deliver any Certified Pre-Owned or used vehicles subject to a delivery stop until the repair is completed.
NHTSA · 제조사 공지10147892원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
losed-circuit Current Measurement. Closed circuit current needs to be measured. Excessive closed-circuit currents may occur continuously or intermittently, and may cause the battery to discharge prematurely. CAUSE The increase in closed-circuit current may be caused by a faulty control unit, or by the installation of a non-approved accessory. INFORMATION In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important to not disconnect the battery. This is because a control unit will be reset if the battery is disconnected. Following a reset, the faulty control unit may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp clip-on probe (previously used with the IMIB) or the 100-amp clip-on probe can now be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time. Connect the amp clip-on probe directly to the IMIB Measurement input 3 (green socket).
NHTSA · 제조사 공지10147825원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a highvoltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use to meet their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging system categories and a simplified tool and battery voltage checking procedure below. INFORMATION To transition the reimbursement of the battery maintenance step from the QCI to the new Battery Care Program described in the procedure section, a reduction in the QCI time allowances was necessary. For more information on the updated QCI payment and the related claim submission information, please refer to SI B01 01 08. Your center will received a separate payment for properly maintaining batteries on in-stock vehicles.
NHTSA · 제조사 공지10147826원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
The Engine Intermittently Loses Power. Intermittently the engine may experience a loss of power along with a Drivetrain Malfunction message. The Service Engine Soon light (MIL) may also be illuminated. There are one or more of the following air mass plausibility and Valvetronic system faults stored in the DME memory: E-series with BN2000 ? 2775 - Air mass, plausibility: Air mass too low ? 2C57 - Charging pressure control, plausibility: Pressure too low ? 2DCE - Valvetronic system: No adjustment possible F-series with BN2020 ? 102002 - Air mass, plausibility: Air mass too low ? 120308 - Charging pressure control, plausibility: Pressure too low ? 133B04 - Valvetronic system: No adjustment possible CAUSE ? Defective Valvetronic component ? Erroneous faults set due to DME software parameters
NHTSA · 제조사 공지10147814원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
"ISPI NEXT ISTA 3.44 introduces a new concept for displaying repair instructions. The new repair instructions have the following advantages compared to the old style: z All instructions (preliminary and follow-up) needed for the repair are included; hyperlinks are no longer needed. z All special tools needed for the repair can be viewed or printed from one tab in ISTA without leaving the repair instructions page. z All technical data and torque specs for the repair can be viewed from one tab in ISTA without leaving the repair instructions page. The most commonly used instructions have been converted to this new format (including repair instructions for the N63 Customer Care Package), and are listed below. Use these instructions instead of the old format. They will save you time and ensure a better quality repair. The Premium instructions can be found in ISTA with a text search for ""Premium."" 1. 1131052 - Replace both timing chains\PREMIUM (N63) 2. 1166000 - Remove and install or replacing vacuum pump\PREMIUM (N63) 3. 1362561 - Removing and installing or replacing both air-mass meters\PREMIUM (N63) 4. 1371190 - Removing and installing/replacing left clean air pipe\PREMIUM (N63) 5. 1371195 - Removing and installing/replacing right clean air pipe\PREMIUM (N63) 6. 1165025 - Removing and installing/replacing right exhaust turbocharger, right\PREMIUM (N63) 7. 1165030 - Removing and installing/replacing left exhaust turbocharger\PREMIUM (N63) 8. 1115001 - Replacing all engine ventilation lines and connection lines\PREMIUM (N63) 9. 1353332 - Replacing fuel feed line\PREMIUM (N63) 10. 1353315 - Removing and installing or replacing all injectors in the fuel injection system\PREMIUM (N63) 11. 5116165 - E70 Completely remove and install the centre console\PREMIUM 12. 6451591 - E90 Removing and installing/renewing evaporator\PREMIUM 13. 1136046 - E90 Removing and installing or replacing intake and exhaust camshaft adjusters\PREMIUM (N55) 14. 1112100 - E90 Removing and install
NHTSA · 제조사 공지10147066원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
BMW Parts Bulletin TEC6X Footwell Module Return BMW AG has requested an inspection of the following part number: 61 35 9 342 897 Stock should not be sold or installed on any vehicle. Concerned are all parts delivered and shipped so far, without a green marker point. All parts with a green marker point are correct and ok to use. (See Image below) Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC6X must appear in the text of your TEC claim. TEC6X is valid from February 03, 2015 through February 17, 2015. The deadline for filing a claim under TEC6X is February 17, 2015. All parts must be returned to your facing RDC no later than March 03, 2015. Please re-order the same part numbers as needed.
NHTSA · 제조사 공지10147092원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
BMW Parts Bulletin TEC8X S-Box with Wiring Harness Return BMW NA has requested the return of the following part numbers: 61 27 8 634 209 Stock should not be sold or installed on any vehicle. Concerned are all parts delivered and shipped so far, which are not marked with a black and green dot. All parts marked with a black and green dot are correct and ok to use. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC8X must appear in the text of your TEC claim. TEC8X is valid from February 13, 2015, through February 27, 2015. The deadline for filing a claim under TEC8X is February 27, 2015. All parts must be returned to your facing RDC no later than March 13, 2015. Please re-order the same number if needed.
NHTSA · 제조사 공지10147093원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
일부 롤스로이스 고스트 모델은 람다 센서(컨트롤 또는 모니터 센서라고도 함)에 올바른 토크가 적용되지 않을 수 있습니다. 높은 품질과 고객 만족도를 유지하기 위해, 롤스로이스 모터카스는 양쪽 엔진 뱅크에 장착된 전후면 람다 센서에 대해 토크 점검을 실시하기로 결정했습니다. 이 절차는 ISPA 또는 S-Gate에 기재된 섀시 번호에 대해 반드시 따라야 합니다.
A small number of Rolls-Royce Ghost, Wraith and Dawn vehicles have been identified as having a potential drivability issue affecting the operation and behavior of the engine under a very specific set of circumstances as well as a problem with data transfer when connected to Rolls-Royce Motor Cars workshop equipment. The problem has been rectified with ISTA (Integrated Service Technical application) programming version 4.13.x which contains vehicle software version F001-18-07-545, available to all Rolls-Royce authorized workshops since 24th August 2018.
NHTSA · 제조사 공지10149549원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
A small number of Rolls-Royce Ghost, Wraith and Dawn vehicles have been identified as having a potential drivability issue affecting the operation and behavior of the engine under a very specific set of circumstances as well as a problem with data transfer when connected to Rolls-Royce Motor Cars workshop equipment. The problem has been rectified with ISTA (Integrated Service Technical application) programming version 4.13.x which contains vehicle software version F001-18-07-545, available to all Rolls-Royce authorized workshops since 24th August 2018.
NHTSA · 제조사 공지10149550원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
"VANOS Faults Stored in DME (Bosch). The Service Engine Soon (MIL) is on and the engine could go into a reduced power mode with the ""Drivetrain Malfunction"" message displayed. One or more of the VANOS faults listed in the attachment are stored in the DME, although the engine is mechanically sound and no unusual noises can be heard from the VANOS area. These control faults relate to implausible camshaft position (intake or exhaust), the camshaft stuck situation, or the camshaft angle offset to crankshaft outside the tolerance range. Due to unfavorable Engine Position Management (EPM) parameters in the DME software, various VANOS control faults could be set."
NHTSA · 제조사 공지10148023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
As a safety precaution, when handling fuel tank always wear safety goggles and plastic (not latex) gloves, Nitrile preferred. 2.Remove defective fuel tank from the vehicle and place it on a workbench in an area where good ventilation is provided. As outlined in SI B01 03 14, starting in March 2014, the initial phase of the E46 SULEV (PZEV) fuel tank remanufacturing process will begin. When this fuel tank is replaced and a corresponding claim is submitted for reimbursement, BMW NA will request that the fuel tank be returned to the Warranty Parts Return Center (WPRC) after claim payment. Please ensure that your workshop technicians and Parts department personnel handle the removed fuel tank(s) properly to avoid unnecessary damage. The fuel tank disposal procedure outlined in the bulletin applies only to non-claim related tank replacements. BMW NA will not request that these tanks be returned to the WPRC. In the case of a non-claim related fuel tank replacement on an E46 3 Series M56 SULEV (PZEV) engine vehicle, the following disposal procedure must be performed prior to scrapping a non-returned requested fuel tank. BEFORE STARTING AND WHILE CONDUCTING THE STEEL FUEL TANK DISPOSAL , FOLLOW ALL LOCAL AND STATE LAWS AND REGULATIONS PERTAINING TO HANDLING OF FLAMMABLE LIQUIDS. DO NOT USE ANY ELECTRICALLY POWERED TOOLS OR OPEN-FLAME DEVICES (E.G., ACETYLENE TORCHES) DURING THIS
NHTSA · 제조사 공지10147919원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
An issue has be identified concerning programming model year 14 onwards Ghost and all Wraith vehicles with ISTA/P version 3.57.1or 3.57.2, which will programme the vehicle to software level F001-15-11-5xx.
NHTSA · 제조사 공지10147899원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
An issue has been identified concerning programming model year 14 onwards Ghost and all Wraith vehicles with ISTA/P version 3.57.1or 3.57.2, which will programme the vehicle to software level F001-15-11-502 or F001-15-11-503. During the programming of these vehicles, the On Board Owner?s Manual is wiped and replaced with a German only version. If the user attempts to search for content in any other language, no content is displayed.
NHTSA · 제조사 공지10147900원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).