Fuel system, gasoline:Storage:Tank assembly
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
🔔 무료 계정을 만들고 Buick Skyhawk (모든 세대) 이메일 알림 받기
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
연료 공급 및/또는 리턴 호스/파이프 어셈블리에 균열이 생기거나 분리되어, 연료가 엔진룸 내부로 누출될 수 있습니다.
On vehicles with 2.0l engines, the fuel feed and return hose assemblies may have been manufactured with improperly crimped fittings.A hose assembly with this condition may crack or separate from the fittng, allowing fuel to leak in the underhood area. This could result in an underhood fire. Correction:Hose assemblies will be replaced.
The engine air cleaner plastic trim cover could fall off the air cleaner assembly and land on the exhaust manifold creating a fire hazard. Consequence of defect: If the car is being operated at the time that the plastic trim cover falls off, an engine compartment fire could occur without warning.
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
Possible fuel leakage could occur at the throttle body injection fuel feed pipe connection on the involved vehicles.
Under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. The fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. Leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.
Under certain conditions the hose clamps on the fuel filler pipe and fuel tank filler vent pipe could fracture. This could cause seepage of fuel at any one of the four pipe to hose connections when the fuel tank is above 3/4 full creating the possibility of fire.
펄스에어 체크 밸브 어셈블리의 내부 부식으로 인해 배기가스가 플라스틱 차단 밸브를 녹이고, 밸브 조각이 에어 클리너와 스로틀 바디로 빨려 들어갈 수 있습니다.
운전석이 수동으로 조절되는 차량에서, 금속 플로어 팬 앵커 바가 왼쪽 앞 바깥쪽 시트 조절 스터드 주변에서 피로 파손되어 부러질 수 있습니다. 이로 인해 스터드가 앵커 바에서 분리되어 운전석이 예고 없이 뒤로 기울어질 수 있으며, 그 결과 차량 제어를 상실하고 사고가 발생할 가능성이 있습니다. 시정 조치: 플로어 팬 앵커 바에 보강 브래킷이 설치될 예정입니다.
The metal floor pan anchor bar could fatigue and break around the left front outer seat adjuster stud of the drivers seat, allowing the stud to separate from the floor pan anchor bar.
Parking brake lever mechanisms may not properly engage when applied as required by fmvss 105. Consequence of defect: Vehicle could unexpectedly roll away uncontrolled, which could result in a vehicle crash.
These vehicles do not comply with c.M.V.S.S.108 - lighting equipment. Buick skyhawk custom 2 and 4 door sedans and limited 4 door sedans.
Incorrect tail lamp lens were installed, lens do not conform to fmvss 108, lamp reflective device and associated equipment. Consequence of defect: In times of reduced visibility, an approaching vehicle may not be aware of this vehicle which could result in a vehicle crash without prior warning.
On certain vehicles, the front seat back locks may not lock under forward load conditions and are therefore not in compliance with CMVSS 207 - Seat Anchorages.
Some vehicles have bucket seat back locks that do not conform to federal motor vehicle safety standard 207, anchorage of seats. In event of a crash, the seat back lock may not function.
The brake proportioner valves may break and separate from the master cylinder. This would allow brake fluid to leak and would result in a partial loss of the brake system.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0).