전기 시스템:점화:스위치
특정 승용차에서 나타나는 문제입니다. 엔진이 시동되지 않는데 운전자가 키를 "시동(start)" 위치에 오랫동안 유지하면, 점화 스위치에 큰 전류가 흐르고, 경우에 따라 그 열로 인해 스위치 내부 부품이 녹을 수 있습니다.
🔔 무료 계정을 만들고 Buick Skylark (모든 세대) 이메일 알림 받기
특정 승용차에서 나타나는 문제입니다. 엔진이 시동되지 않는데 운전자가 키를 "시동(start)" 위치에 오랫동안 유지하면, 점화 스위치에 큰 전류가 흐르고, 경우에 따라 그 열로 인해 스위치 내부 부품이 녹을 수 있습니다.
Certain vehicles, after being exposed to substantial amounts of water, may experience deployment of either the driver or passenger front airbag without a crash. The owner’s manual for these vehicles does not provide specific information about this situation. Inadvertent deployment of the driver and / or passenger front airbag in a non-accident (non-impact) situation may cause damage to the surrounding vehicle environment (windshield / instrument panel), and create expensive vehicle repair, including replacement of the airbag module(s) and the Sensing and Diagnostic Module (SDM). In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: GM will notify the owners of these 1996 and 1997 vehicles of the potential affect of water accumulating in the vehicle interior on the function of the airbag system (as included in the owner's manuals of 1998 and later model years vehicles).
On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal switch parts.
Vehicle description: Passenger vehicles. If the engine starter fails to engage and the driver hold the key in the "start" position for an extended period, high current flows through the ignition switch, producing heat that can melt switch parts.
The protective cover for the underhood fuse centre may have been omitted on these vehicles. Without this cover, the positive terminal bolt on the fuse block is exposed, and may come in contact with the insulated negative battery cable. Prolonged contact may result in abrasion of the negative cable insulation and could cause an extremely high current short circuit between the positive terminal and the negative cable. This current flow could cause arcing and result in an underhood fire. Correction: A protective cover will be installed if necessary.
The protective cover for the underhood fuse center was omitted. Without this cover, the positive terminal bolt on the fuse block is exposed and can contact the insulated negative battery cable. If the insulation on the negative cable becomes sufficiently worn, an electrical short circuit can occur between the positive terminal and negative cable resulting in extremely high current flow.
The steering column lower pinch bolt was not properly tightened during assembly.
The steering column lower pinch bolt may not have been torqued to specification. This could result in rattle and looseness in the steering system. If the pinch bolt were backed out of the joint completely, rotation of the steering shaft against the connector in high effort steering maneuvers could cause increasing looseness in the steering system and could result in loss of steering and a crash. Correction: Steering column pinch bolt will be inspected and if necessary tightened to specified torque.
These vehicles may not comply with c.M.V.S.S. 301 - fuel system integrity. Some welds in the left rear quarter panel may have been missed during assembly. In the event of a vehicle crash, the vehicle sheet metal structure may not perform as designed. This could result in unexpected damage to the fuel tank or fuel lines and leakage of fuel. If there is a fuel leak and an ignition source, a fire could occur. Correction: Dealers will inspect for missing welds and, if necessary, place three welds between the involved panels.
During assembly of the left rear quarter panel, some welds were missed. This does not comply with the requirements of fmvss no. 301, "fuel system integrity."
These vehicles were constructed with welds in the rear compartment pan assembly that are not sufficient to comply with the requirements pertaining to fuel tank leakage in the event of a rear impact collision. The fuel tank assemblies do not comply with fmvss no. 301, "fuel system integrity."
앞쪽 연료 공급 호스 어셈블리가 호스 어셈블리의 엔진 쪽 커플링 부위에서 균열이 생기거나 분리될 수 있으며, 이로 인해 연료가 엔진 룸으로 누출될 수 있습니다.
수분이 express-down 전자 제어 모듈(electronic control module)에 유입되어 단락(short circuit)을 일으킬 수 있으며, 이로 인해 운전자의 조작 없이 창문이 작동하고 창문이 내려간 상태로 남을 수 있습니다.
차량에 파워 윈도우가 장착된 경우, 습기가 express-down 전자 제어 모듈(ECM)로 유입될 수 있으며, 이로 인해 운전자가 조작하지 않아도 창문이 작동하는 "팬텀 윈도우 작동" 현상이 발생할 수 있습니다. 창문이 스스로 오르내리기를 반복하거나 때로는 내려간 상태로 멈춰 있을 수 있습니다. 모듈은 결국 과열되어 고장날 수 있으며, 이 경우 도어 패널 내부에서 화재가 발생할 수 있습니다. 시정 조치: 딜러가 파워 윈도우 express-down 전자 제어 모듈을 교체합니다.
The daytime running light (drl) module, which is located near the battery, could overheat and possibly result in an underhood fire. Correction: Dealers will replace the drl module, install a wiring harness with fuses and install a module cover.
Improperly torqued connections of front fuel feed and return hoses to fuel pipes at the body rail could loosen and leak fuel into the underhood area.
Vehicles may have improperly torqued connections of the front fuel feed/return hoses to the fuel pipes at the body rail. A fitting may loosen enough to leak fuel into the underhood area, and, in the presence of an ignition source, a fire could result. Correction: Front fuel feed/return hose fittings will be properly torqued.
On vehicles with quad 4 engines, the front fuel feed assembly could crack or separate at the coupling on the engine end of the assembly, allowing fuel to leak into the underhood area. This would create the possibility of an engine compartment fire. Correction: Front fuel feed hose assembly will be replaced on affected vehicles.
Front fuel feed hose assembly could crack or separate at the coupling on the engine end of the hose assembly, allowing fuel to leak into the engine compartment.
The fuel feed or fuel return hose at the engine may rub against a shift lever on the 5 speed transaxle.
2.5리터 엔진 차량의 경우. 연료 시스템이 스로틀 바디 분사 연료 공급 파이프 연결부에서 누유가 발생할 수 있어 보닛 아래 화재 가능성을 제기합니다.
연료 시스템은 스로틀 바디 분사 연료 공급 파이프 연결 부에서 누수가 발생할 수 있습니다. 결함의 결과: 이 누출은 후드 아래 화재를 초래할 수 있으며, 이는 승객 구역으로 번져 탑승자에게 화상 부상을 입힐 수 있습니다.
The rear control arm bracket attaching bolts used on certain of these vehicles may fracture. Failure of all four bolts on one side can result in the control arm dropping enough to cut the rear brake hose. Such a cut would result in fluid loss and partial loss of braking action. This would cause increased stopping distances and should a failure occur while trhe vehicle is in motion at a time when minimal stopping distances are required, a vehicle crash could result.
The rear axle control arm locates and helps control axle movement; it attaches to the frame with a bracket. The rear control arm bracket attaching bolts used on some of the involved vehicles may fracture. Fracture of all four bolts on one side of the vehicle can result in the control arm dropping enough to cut the rear brake hose. A severed brake hose would result in brake fluid loss and partial loss of braking ability.
The brake proportioner valves may break and separate from the master cylinder during braking. This will result in a loss of brake fluid and a partial loss of braking action
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).