무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

DodgeDodge 차저

2024– · 1 세대 · 결함 5건 · 1개 시장
세대
모든 세대(2024)2024–54232

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

공지보통엔진NA

공지

oil filter If an engine oil leak develops from gasket of a newly installed MOPAR engine oil filter, please replace it with an equivalent BPro brand engine oil filter.

NHTSA · 제조사 공지11038784연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2096-00 - Post Catalyst Fuel Trim System Too Lean (Bank 1). P2097-00 - Post Catalyst Fuel Trim System Too Rich (Bank 1). P2098-00 - Post Catalyst Fuel Trim System Too Lean (Bank 2). P2099-00 - Post Catalyst Fuel Trim System Too Rich (Bank 2). P032F-00 - Combustion Engine Producing Insufficient Torque. P2D28-00 - Cold Start Propulsion Torque Performance. U0075-00 - Control Module Communication Bus "C" Off. P0610-00 - Control Module Vehicle Options Error. P0630-00 - VIN Not Programmed or Incompatible - ECM/PCM. P0607-00 - Control Module Performance. P0513-00 - Incorrect Immobilizer Key. C0501-00 - Left Front Wheel Speed Sensor "A" Range/Performance. C0507-00 - Right Front Wheel Speed Sensor "A" Range/Performance. C050D-00 - Left Rear Wheel Speed Sensor "A" Range/Performance. C0513-00 - Right Rear Wheel Speed Sensor "A" Range/Performance. P0520-00 - Engine Oil Pressure Sensor/Switch "A" Circuit. P0139-00 - O2 Sensor Circuit Slow Response (Bank 1 Sensor 2). P0159-00 - O2 Sensor Circuit Slow Response (Bank 2 Sensor 2). P0300 - Random/Multiple Cylinder Misfire Detected. P0301 - Cylinder 1 Misfire Detected. P0302 - Cylinder 2 Misfire Detected. P0303 - Cylinder 3 Misfire Detected. P0304 - Cylinder 4 Misfire Detected. P0305 - Cylinder 5 Misfire Detected. P0306 - Cylinder 6 Misfire Detected.** Customers may also experience **one or more of ** the following: **Vehicle exhibits a no crank / no start condition.** Vehicle does not meet evaporative emissions requirements. **In addition, the following software enhancement(s) are available: Launch Control and HMI improvements. Resolved false "Oil Level Low" warnings when vehicle is parked on an incline.** This bulletin involves inspecting and possibly reprogramming the PCM **and/or TCM** with the latest available software

NHTSA · 제조사 공지11038771연식 2027원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Transmission Control Module (TCM) Updates PCR9A Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P1625-00 - Park Pawl System Failure. NOTE: The above DTCs are being falsely set due to lack of robustness to the diagnostic monitor. Customers may also comment on one or more the following: **Slow downshifting when in manual mode.** Vehicle exhibits a no crank / no start condition. This bulletin involves inspecting and possibly reprogramming the TCM, PCM and ISCM with the latest available software

NHTSA · 제조사 공지11038314연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates PCR9A Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P032F-00 - Combustion Engine Producing Insufficient Torque. P2D28-00 - Cold Start Propulsion Torque Performance. U0075-00 - Control Module Communication Bus "C" Off. P0610-00 - Control Module Vehicle Options Error. P0630-00 - VIN Not Programmed or Incompatible - ECM/PCM. P0607-00 - Control Module Performance. P0513-00 - Incorrect Immobilizer Key. C0501-00 - Left Front Wheel Speed Sensor "A" Range/Performance. C0507-00 - Right Front Wheel Speed Sensor "A" Range/Performance. C050D-00 - Left Rear Wheel Speed Sensor "A" Range/Performance. C0513-00 - Right Rear Wheel Speed Sensor "A" Range/Performance. P0520-00 - Engine Oil Pressure Sensor/Switch "A" Circuit. P0139-00 - O2 Sensor Circuit Slow Response (Bank 1 Sensor 2). P0159-00 - O2 Sensor Circuit Slow Response (Bank 2 Sensor 2).** P2096-00 - Downstream Fuel Trim System 1 Lean. P2097-00 - Downstream Fuel Trim System 1 Rich. P2098-00 - Downstream Fuel Trim System 2 Lean. P2099-00 - Downstream Fuel Trim System 2 Rich. P068A-00 - ECM Power De-Energized Performance-Too Early. NOTE: The above DTCs are being falsely set due to lack of robustness to the diagnostic monitor. P121B-00 - Active Exhaust Valve 2 Performance. P1217-00 - Active Exhaust Valve 1 Performance. P0172-00 - System To Rich (Bank 1). P0175-00 - Fuel System 2/1 Rich. Customers may also comment on the following: Vehicle exhibits a no crank / no start condition. Exhaust pitch does not track with acceleration. **In addition, the following software enhancement(s) are available: Launch Control Feature improvements. Resolved "Oil Level Low" warning caused by parking on incline.** This bulletin involves inspecting and possibly reprogramming the PCM, TCM and ISCM with the latest available software

NHTSA · 제조사 공지11038311연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

PUMP, Auxiliary Coolant, High Temperature Before replacing the High Temperature Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.

NHTSA · 제조사 공지11036368연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Flash: Body Control Module (BCM) Update Technicians may find the following Diagnostic Trouble Code (DTC): SYMPTOM: B18AA-11 - Trunk/Gate Unlock Control 1-Circuit Short to Ground. NOTE: There are no Malfunction Indicator Lamp (MIL) illumination or related messages displaying in the Instrument Panel Cluster (IPC) for this symptom. **Hatch event only occurs on BEV vehicles without JRC for Power Hatch.** Customers may comment on the following: **Battery is depleted. When at a full stop and the Engine Stop Start (ESS) has turned off the engine, the engine does not automatically restart once the brake pedal is released. This is accompanied by a chime and a pop-up message on the IPC indicating ESS has aborted. The vehicle can be restarted once shifted into Park and pressing the ignition button. NOTE: These symptoms occur due to the BCM sending an incorrect hood position message. The ESS event only occurs on ICE equipped vehicles.** The hatch will not open when a release button (interior, exterior, or Frequency Operated Button Integrated Key (FOBIK)) is pressed. NOTE: **Hatch event only occurs on BEV vehicles without JRC for Power Hatch.** This bulletin involves inspecting and possibly reprogramming the BCM with the latest available software.

NHTSA · 제조사 공지11036351연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash. If correct repair is not performed then the claim or condition will be recovered by Warranty Operations.

NHTSA · 제조사 공지11035994연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Transmission Control Module (TCM) Diagnostic Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following DTCs: P2797-00 - Auxiliary Transmission Fluid Pump Performance P1625-00 - Park Pawl System Failure NOTE: Park system still functions, no impact to park engagement. NOTE: Vehicle will not experience unintended movement. Customers may also experience one or more of the following: Vehicle no start due to battery discharge. 'Start/stop inop' message. 'Service Transmission' message on in Instrument Panel Cluster (IPC).

NHTSA · 제조사 공지11035313연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Inspect battery terminals for damage to rule out a battery drainage issue. 6) Ensure the PCM is up-to-date with the latest available flash.

NHTSA · 제조사 공지11035194연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

PUMP, Auxiliary Coolant Before replacing the Auxiliary Coolant Pump, please perform the following steps: 1) Key ON/OFF and let the after-run pump run for at least 20 minutes before moving on to step #2. 2) Inspect the pump connector area for presence of water. 3) Inspect the pump connector for corrosion. 4) Inspect the pump for coolant contamination as this can cause the pump to stall. 5) Ensure the PCM is up-to-date with the latest available flash. 6) Inspect battery terminals for damage to rule out a battery drainage issue.

NHTSA · 제조사 공지11035070연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2096-00 - Downstream Fuel Trim System 1 Lean. P2097-00 - Downstream Fuel Trim System 1 Rich. P2098-00 - Downstream Fuel Trim System 2 Lean. P2099-00 - Downstream Fuel Trim System 2 Rich. P068A-00 - ECM Power De-Energized Performance-Too Early. NOTE: The above DTCs are being falsely set due to lack of robustness to the diagnostic monitor. P121B-00 - Active Exhaust Valve 2 Performance. P1217-00 - Active Exhaust Valve 1 Performance. Customers may also comment on the following: Vehicle exhibits a no crank / no start condition. Exhaust pitch does not track with acceleration. This bulletin involves inspecting and possibly reprogramming the PCM, TCM and ISCM with the latest available software.

NHTSA · 제조사 공지11032977연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Transmission Control Module (TCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P1625-00 - Park Pawl System Failure. P2096-00 - Downstream Fuel Trim System 1 Lean. P2097-00 - Downstream Fuel Trim System 1 Rich. P2098-00 - Downstream Fuel Trim System 2 Lean. P2099-00 - Downstream Fuel Trim System 2 Rich. P068A-00 - ECM Power De-Energized Performance-Too Early. NOTE: The above DTCs are being falsely set due to lack of robustness to the diagnostic monitor. Customers may also comment on the following: Vehicle exhibits a no crank / no start condition. This bulletin involves inspecting and possibly reprogramming the TCM, PCM and ISCM with the latest available software.

NHTSA · 제조사 공지11032978연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Flash: Ignition System Control Module (ISCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2096-00 - Downstream Fuel Trim System 1 Lean. P2097-00 - Downstream Fuel Trim System 1 Rich. P2098-00 - Downstream Fuel Trim System 2 Lean. P2099-00 - Downstream Fuel Trim System 2 Rich. P068A-00 - ECM Power De-Energized Performance-Too Early. NOTE: The above DTCs are being falsely set due to lack of robustness to the diagnostic monitor. Customers may also comment on the following: Vehicle exhibits a no crank / no start condition. This bulletin involves inspecting and possibly reprogramming the ISCM, TCM and PCM with the latest available software.

NHTSA · 제조사 공지11032975연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

26MY LB Six Pack: Customer complained about water leaking from the hood bezel into the hood. This is a non-issue since engineering intent is for the water to drain onto the hood inner and then toward beauty cover. Replacement parts will act in the same manner.

NHTSA · 제조사 공지11031335연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Module - steering wheel

NHTSA · 제조사 공지11031229연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"

NHTSA · 제조사 공지11030427연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Before replacing the water pump on 3.0L SO/HO, please follow the updated WATER PUMP INSPECTION diagnostic procedure to confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"

NHTSA · 제조사 공지11030426연식 2026원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. P1614-00 - ECU Reset/Recovery Occurred. B1A8A-00 - Multi-Module VIN Handshake Failure. P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. P1E25-00 - EV Battery Failure Level 2. P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. P1CDE-00 - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. P1CDA-00 - Hybrid/EV Wakeup Control 1 Output Circuit/Open. U00C6-00 - Lost Communication With AIR Pressure Sensor. P0F00-00 - Hybrid/EV Battery Module 1 Performance. P0F01-00 - Hybrid/EV Battery Module 2 Performance. P0F02-00 - Hybrid/EV Battery Module 3 Performance. P0F03-00 - Hybrid/EV Battery Module 4 Performance. P0F04-00 - Hybrid/EV Battery Module 5 Performance. P0F05-00 - Hybrid/EV Battery Module 6 Performance. P0F06-00 - Hybrid/EV Battery Module 7 Performance. P0F07-00 - Hybrid/EV Battery Module 8 Performance. P0F08-00 - Hybrid/EV Battery Module 9 Performance. P0F09-00 - Hybrid/EV Battery Module 10 Performance. P0F0A-00 - Hybrid/EV Battery Module 11 Performance. P0F0B-00 - Hybrid/EV Battery Module 12 Performance. P0F0C-00 - Hybrid/EV Battery Module 13 Performance. P0CA6-00 - Hybrid/EV Battery Charging Current High NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: Vehicle will not start. A warning message will appear in the Instrument Panel Cluster (IPC) informing the driver to stop safely because the vehicle will be shutting down soon. Wrench icon is illuminated on the IPC. Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: Software enhancements to prevent multiple DTCs from falsely setting. Improved battery State of Charge (SoC) accuracy in off-nominal conditions. Bootloader update to prevent battery disconnect unit damage. Improvements in detecting pre-existing battery disconnect unit damage. Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.

NHTSA · 제조사 공지11030130연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. P1614-00 - ECU Reset/Recovery Occurred. B1A8A-00 - Multi-Module VIN Handshake Failure. P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. P1E25-00 - EV Battery Failure Level 2. P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. P1CDE-00 - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. P1CDA-00 - Hybrid/EV Wakeup Control 1 Output Circuit/Open. U00C6-00 - Lost Communication With AIR Pressure Sensor. P0F00-00 - Hybrid/EV Battery Module 1 Performance. P0F01-00 - Hybrid/EV Battery Module 2 Performance. P0F02-00 - Hybrid/EV Battery Module 3 Performance. P0F03-00 - Hybrid/EV Battery Module 4 Performance. P0F04-00 - Hybrid/EV Battery Module 5 Performance. P0F05-00 - Hybrid/EV Battery Module 6 Performance. P0F06-00 - Hybrid/EV Battery Module 7 Performance. P0F07-00 - Hybrid/EV Battery Module 8 Performance. P0F08-00 - Hybrid/EV Battery Module 9 Performance. P0F09-00 - Hybrid/EV Battery Module 10 Performance. P0F0A-00 - Hybrid/EV Battery Module 11 Performance. P0F0B-00 - Hybrid/EV Battery Module 12 Performance. P0F0C-00 - Hybrid/EV Battery Module 13 Performance. P0CA6-00 - Hybrid/EV Battery Charging Current High. M08 FSAR-TSB-7132 -2- NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. P0ADB-00 - Hybrid/EV Battery Positive Contract

NHTSA · 제조사 공지11030120연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P1E18-00 - Internal Control Module Electronic Park Performance. P1625-00 - Park Pawl System Failure. P0A78-00 - Drive Motor A Inverter Performance. P0A79-00 - Drive Motor B Inverter Performance. P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following symptoms: Vehicle will not power down causing a 12V battery drain. Vehicle does not start. Wrench icon is illuminated on the Instrument Panel Cluster (IPC). Turtle icon illuminated on the IPC. Reduced power. Vehicle will not shift out of park. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.

NHTSA · 제조사 공지11030007연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P1E18-00 - Internal Control Module Electronic Park Performance. P1625-00 - Park Pawl System Failure. P0A78-00 - Drive Motor A Inverter Performance. P0A79-00 - Drive Motor B Inverter Performance. P1626-00 - Park Pawl Motor Stuck. The customer may comment on one or more of the following symptoms: Vehicle will not power down causing a 12V battery drain. Vehicle does not start. Wrench icon is illuminated on the Instrument Panel Cluster (IPC). Turtle icon illuminated on the IPC. Reduced power. Vehicle will not shift out of park. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.

NHTSA · 제조사 공지11030006연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): B12B4-00 - Charge Status Indicator Module Internal. C10FA-00 - Wheel Hub disconnect Actuator Performance Left. C10FB-00 - Wheel Hub disconnect Actuator Performance Right. C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: Loss of communication between EVCU and the Battery Pack Control Module (BPCM) can prevent high- voltage contactors from closing, resulting in a no-start condition. Remote start functionality fails when the vehicle is actively charging. "Charge Now" feature in application has multiple issues. Feature intermittently fails and does not close contactors, sometimes starts but charge port indicator lights are not commanded by EVCU and sets DTC B12B4-00. Closed loop 12V silent charging which can help mitigate a 12V drain issue on the vehicle. Drive-by-brake improvements and a resolved issue where the vehicle incorrectly enters turtle mode while driving. Powershot sometimes stuck at 0 seconds remaining which makes customer believe that Powershot is not working. Wheel End Disconnect closure at zero speed in case of miss at normal close speed. Drive-by-brake message update to Instrument Panel Cluster (IPC) in case of Limp Home mode. Vehicle will not start due to depleted 12v battery. Improvements to minimize occurrences of Limp Home Mode (Turtle Mode). IPC, radio range and charge time estimations and messages are not correct. Battery range incorrect. Improved battery State of Charge (SoC) accuracy in off-nominal conditions.

NHTSA · 제조사 공지11030005연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Flash: Electronic Vehicle Control Unit (EVCU) Updates 6B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C10FA-00 - Wheel Hub disconnect Actuator Performance Left. C10FB-00 - Wheel Hub disconnect Actuator Performance Right. C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: Will not be able to start the vehicle. 12V battery dead resulting in no start. Loss of communication between EVCU and BPCM can prevent high-voltage contactors from closing, resulting in a no-start condition. Powershot sometimes stuck at 0 seconds remaining which makes customer believe that Powershot is not working. Remote start functionality fails when the vehicle is actively charging "Charge Now" feature in app - multiple issues. Sometimes fails and does not close contactors, sometimes starts but CPIM lights are not commanded by EVCU and sets B12B4. WED closure at zero speed in case of miss at normal close speed. Drive-by-brake HMI message update to IPC in case of Limp Home mode. DTC U0594 setting after pedal learn (applicable only for plant). Instrument Panel Cluster (IPC), radio range and charge time estimations and messages are not correct. Battery range incorrect. Improved battery State of Charge (SoC) accuracy in off-nominal conditions. Battery heating values incorrect on radio when on Performance Pages display. Charging does not start when plugged in. Charging is not indicating when battery is at full charge. Charging slow or takes too long. Bumps and jerks while accelerating or decelerating. Wrench icon is illuminated on the IPC. Turtle icon is illumina

NHTSA · 제조사 공지11030002연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Motor Control Processor B (MCP B) Updates 6B3 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P1E18-00 - Internal Control Module Electronic Park Performance. P1625-00 - Park Pawl System Failure. P0A78-00 - Drive Motor A Inverter Performance. P0A79-00 - Drive Motor B Inverter Performance. P1626-00 - Park Pawl Motor Stuck. The customer may comment on one or more of the following symptoms: Vehicle not shutting off and a draining 12V battery. Vehicle no start. Wrench icon is illuminated on the Instrument Panel Cluster (IPC). Turtle icon illuminated on the IPC. Reduced power. Vehicle will not shift out of park. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.

NHTSA · 제조사 공지11030003연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Flash: Motor Control Processor A (MCP A) Updates 6B3 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P1E18-00 - Internal Control Module Electronic Park Performance. P1625-00 - Park Pawl System Failure. P0A78-00 - Drive Motor A Inverter Performance. P0A79-00 - Drive Motor B Inverter Performance. P1626-00 - Park Pawl Motor Stuck. The customer may comment on one or more of the following symptoms: Vehicle not shutting off and a draining 12V battery. Vehicle no start. Wrench icon is illuminated on the Instrument Panel Cluster (IPC). Turtle icon illuminated on the IPC. Reduced power. Vehicle will not shift out of park. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.

NHTSA · 제조사 공지11030004연식 2025원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).