무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

DodgeDodge Dart

2012–2016 · 1 세대 · 결함 9건 · 3개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

공지보통엔진NA

공지

Customer Complaint May Include Engine Oil Leak Or Consumption

NHTSA · 제조사 공지10221277연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Customer Complaint May Include Engine Oil Leak Or Consumption

NHTSA · 제조사 공지10212473연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Tube - brake

NHTSA · 제조사 공지10170347원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Flash: 2.0L Diagnostic And System Improvements software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0335-00 - Crankshaft Position Sensor Circuit.** P030X - Cylinder X Misfire improvements when P0335 (Crankshaft Position Sensor Circuit) is present. P0116 - Engine Coolant Temperature Sensor 1 Performance. P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P1D73 - AGS (Active Grill Shutter) Performance. U0140 - Lost Communication With Body Control Module (BCM). In addition to the above conditions, a customer may also experience the following symptoms: ASD/Fuel pump relay cycling during remote start. E15 cold start improvements in temperatures below -7C (20F).

NHTSA · 제조사 공지10228107연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P1185 - General Pressure Sensor Correlation.** P0335 - Crankshaft Position Sensor Circuit. P050D - Cold Start Rough Idle. P0456 - Evap System Small Leak. P0133 - O2 Sensor 1/1 Slow Response (additional enhancements). P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. **In addition to the above DTCs, this software release also includes these enhancements/corrections: A ?Clunk feeling" when depressing the gas pedal after a coasting maneuver when Decel Fuel Shut Off (DFSO) is enabled and is exiting during pedal tip-in.** False reading that the engine is overheating based on the engine oil temp gauge read out. Improved ambient temperature sensor diagnostics during sunload. Disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

NHTSA · 제조사 공지10228108연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: 2.0L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0335-00 - Crankshaft Position Sensor Circuit.** P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P1607 - PCM Internal Shutdown Timer Rationality. In addition to the above DTCs, this software release also includes: Enhancements to the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present. Re-Activation of Electronic Throttle Control (ETC) (2.0L MTX only). Engine oil temperature gauge calibration enhancement.

NHTSA · 제조사 공지10228116연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.

NHTSA · 제조사 공지10224875연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통기타NA

공지

Rear Shelf Panel Replacement This bulletin involves replacing the rear shelf panel. The customer may describe poor rear speaker performance due to an incorrect rear shelf panel installed in the vehicle.

NHTSA · 제조사 공지10223820연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

NHTSA · 제조사 공지10223853연식 2015원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통엔진NA

공지

Some of the above vehicles may experience an engine stall when the engine is first started while the outside ambient air temperature is 20 degrees or lower and the vehicle is operated under certain driving conditions.

NHTSA · 제조사 공지10220406연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Front Brake Noise (Squeal) This bulletin involves changing front brake pads to correct a brake squeal noise. The customer may experience a squealing noise during braking coming from the front of the vehicle.

NHTSA · 제조사 공지10218808연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Front Brake Noise (Squeal) This bulletin involves changing front brake pads to correct a brake squeal noise. The customer may experience a squealing noise during braking coming from the front of the vehicle.

NHTSA · 제조사 공지10217967연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: 2.0L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may describe a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following DTCs set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance.** U0140 - Lost Communication With Body Control Module. P1D73 - AGS Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. P0456 - Evap System Small Leak. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Electronic Vehicle Information Center (EVIC) Fuel Economy display accuracy. Improved Enhanced Automatic Oil Change Indicator (EAOCI) system accuracy. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

NHTSA · 제조사 공지10217615연식 2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience the Electronic Vehicle Information Center (EVIC) Fuel Economy display is inaccurate or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? U0140 - Lost Communication With Body Control Module. ? P1D73 - AGS Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P0456 - Evap System Small Leak. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? Improved Enhanced Automatic Oil Change Indicator (EAOCI) system accuracy. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

NHTSA · 제조사 공지10217432연식 2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0133 - O2 Sensor 1/1 Slow Response. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include an engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

NHTSA · 제조사 공지10217436연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Driveability Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream ? P1D73 - 00 - AGS Performance ? P1CEA - Boost Side Evap Purge System Performance ? P0456 - Evap System Small Leak Customers may also experience any of the following symptoms: ? Customer experiences cold start issues below 14F ( -10C) ambient temperatures; engine turns over faster (loss of compression) during crank and possibly does not start until a key cycle is performed. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? Spark knock when using low octane fuel in the vehicle. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Uneven acceleration feeling under moderate to heavy throttle input. ? Bump or surge noticed prior to engine reaching normal operating temperature. ? Rough idle during A/C engagement/disengagement. ? During periods of extended idle or short hot soak events and ambient temperatures below 15F (-9C), engine idle speed may increase to 1800 RPM if coolant temperature drops below 158F (70C). Condition is only present when the transmission is in park. ? Low speed engine response improvements in city and traffic driving conditions. Updating the PCM software will correct the condition listed above.

NHTSA · 제조사 공지10217430연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: No Start or Start and Stall When Using Remote Start This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: ? Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?) ? Engine cranks and does not start following the condition described above ? Engine may be hard to re-start at ambient temps below 10F(-12C) Updating the software will correct the conditions listed above.

NHTSA · 제조사 공지10216450연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통브레이크NA

공지

Rattle From Front Brakes When Driving, Without Brakes Applied This bulletin involves replacing the front brake caliper brackets, spring clips and if necessary front brake pads. Rattle from front brakes when driving, without brakes applied

NHTSA · 제조사 공지10216440연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Driveability Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream ? P1D73 - 00 - AGS Performance ? P1CEA - Boost Side Evap Purge System Performance ? P0456 - Evap System Small Leak Customers may also experience any of the following symptoms: ? Customer experiences cold start issues below 14F ( -10C) ambient temperatures; engine turns over faster (loss of compression) during crank and possibly does not start until a key cycle is performed. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? Spark knock when using low octane fuel in the vehicle. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Uneven acceleration feeling under moderate to heavy throttle input. ? Bump or surge noticed prior to engine reaching normal operating temperature. ? Rough idle during A/C engagement/disengagement. ? During periods of extended idle or short hot soak events and ambient temperatures below 15F (-9C), engine idle speed may increase to 1800 RPM if coolant temperature drops below 158F (70C). Condition is only present when the transmission is in park. ? Low speed engine response improvements in city and traffic driving conditions. Updating the PCM software will correct the condition listed above.

NHTSA · 제조사 공지10216192연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience the Electronic Vehicle Information Center (EVIC) Fuel Economy display is inaccurate or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? U0140 - Lost Communication With Body Control Module. ? P1D73 - AGS Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P0456 - Evap System Small Leak. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? Improved Enhanced Automatic Oil Change Indicator (EAOCI) system accuracy. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

NHTSA · 제조사 공지10216194연식 2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0133 - O2 Sensor 1/1 Slow Response. In addition, some customers may describe that the engine is overheating based on the engine oil temp gauge read out. Software improvements include an engine oil temperature gauge level recalibration to avoid the misperception of an engine overheating condition.

NHTSA · 제조사 공지10216198연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통변속기NA

공지

Flash: No Start or Start and Stall When Using Remote Start This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software and updating the Body Control Module (BCM) software. A small number of customers may experience any of the following conditions: Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?) Engine cranks and does not start following the condition described above Engine may be hard to re-start at ambient temps below 10F(-12C)Updating the software will correct the conditions listed above.

NHTSA · 제조사 공지10215979연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

Rattle And/Or Buzz At The Right Rear Of Vehicle And/Or Fuel Door Difficult To Open This bulletin involves inspecting and if necessary modifying the fuel filler housing. It may also involve inspecting the fuel filler door and if necessary reinstalling or replacing the fuel filler housing. Rattle and/or buzz at the right rear of vehicle and/or fuel door difficult to open.

NHTSA · 제조사 공지10215989연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통기타NA

공지

Remote Start Option Missing This Bulletin involves installing a Mopar remote start kit. The customer and or dealer may note that the remote start option is missing from the vehicle. The Monroney label will shows the vehicle having this feature.

NHTSA · 제조사 공지10215992연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통차체NA

공지

This bulletin involves inspecting and if necessary modifying the fuel filler housing. It may also involve inspecting the fuel filler door and if necessary reinstalling or replacing the fuel filler housing. Rattle and/or buzz at the right rear of vehicle and/or fuel door will not open.

NHTSA · 제조사 공지10215819연식 2013원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).