전기 시스템
1996년부터 1998년까지 캔자스시티 쿠아티틀란 조립 공장에서 제작된 일부 승용차나 1999년 오토모티얼라이언스 국제 조립 공장에서 제작된 승용차에서, 히터 블로어 저항기의 스테인리스 블레이드의 거친 표면이 배선 하니스 커넥터의 구리 표면을 손상시킬 수 있습니다. 이 손상은 시간이 지남에 따라 커넥터 저항을 증가시키고, 이후 단자 이완으로 인해 개방 회로 상태를 초래할 수 있습니다.
🔔 무료 계정을 만들고 Ford Contour 이메일 알림 받기
1996년부터 1998년까지 캔자스시티 쿠아티틀란 조립 공장에서 제작된 일부 승용차나 1999년 오토모티얼라이언스 국제 조립 공장에서 제작된 승용차에서, 히터 블로어 저항기의 스테인리스 블레이드의 거친 표면이 배선 하니스 커넥터의 구리 표면을 손상시킬 수 있습니다. 이 손상은 시간이 지남에 따라 커넥터 저항을 증가시키고, 이후 단자 이완으로 인해 개방 회로 상태를 초래할 수 있습니다.
Vehicle description: Bi-fuel vehicles. These vehicles may have a fuel tank filler pipe grommet that could have been damaged during the installation of the bi-fuel system. If the grommet is damaged, fuel could leak. Fuel leakage in the presence of an ignition source could result in a fire. Dealers will replace the fuel tank filler pipe grommet.
On certain vehicles, the fuel filler pipe vent hose may have less than the intended level of ozone resistance, which could result in the hose becoming brittle and cracking. A cracked hose could result in fuel leakage when the vehicle is being fueled. Fuel leakage in sufficient quantity in the presence of an ignition source could potentially result in a fire. Correction: Dealers will install a fuel filler vent hose containing the appropriate blend of PVC and nitrile rubber.
Vehicle description: Passenger vehicles. The fuel filler pipe vent hose may have less than the intended level of ozone resistance, which could result in the hose becoming brittle and cracking.
Vehicle description: Bi-fuel vehicles modified to run on either gasoline or compressed natural gas (cng). The natural gas fuel tanks have a solenoid shut-off valve that stops fuel flow from the fuel tank in the event of certain moderate to severe collisions. If the vehicle is in a collision and the natural gas fuel line is damaged, the system could leak natural gas.
The fuel tank filler pipe opening reinforcement, fabricated from two separately moulded pieces spin welded together, may eventually leak fuel at the weld joint. Fuel leakage in the presence of an ignition source, could potentially result in a fire. Correction: Fuel tank assemblies will be replaced with ones containing one piece moulded reinforcements.
The fuel tank filler pipe opening reinforcement, constructed from two separately molded pieces, can leak at the weld.
The passenger side supplemental restraint system (air bag) may have a cracked inflator body. If the vehicle is involved in a deployment level crash, the passenger side air bag may not inflate properly which could result in reduced occupant protection. In addition, the igniter plug could separate from the inflator, which could result in the release of hot gases and could ignite flammable material or potentially cause personal injury. Correction: Vehicles will be inspected and a new passenger side air bag module will be installed if necessary.
The fuel tank filler pipe opening reinforcement can leak at the weld.
The fuel filler opening reinforcement (an integral part of the fuel tank assembly) may leak fuel. In the presence of an ignition source, a fire could result. Correction: Fuel tank will be replaced on affected vehicles.
A metal shield on the outside of the plastic fuel filler pipe can develop a static electrical charge during refueling of the vehicle.
Vehicle description: Passenger vehicles built at the kansas city assembly plant and originally sold in or currently registered in the states of connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, and wisconsin, and the district of columbia. The front coil springs may fracture as a result of corrosion in high corrosion environments. Depending on the location of the fracture, a broken spring could move past the spring seat and contact a front tire.
Vehicle description: Passenger vehicles built with an incorrect power brake booster and master cylinder assembly.
차량 설명: 2.0L 및 2.5L 엔진이 장착된 1995년식 승용차 및 2.5L 엔진이 장착된 1996년식 차량. 엔진 냉각팬 모터 베어링이 조여지면서 모터 정지(stall)에 이르기까지 모터 토크가 증가하고, 정상보다 높은 모터 전류와 그에 따른 높은 모터 온도가 발생할 수 있습니다.
차량 설명: TRW 안전벨트 버클 어셈블리가 장착된 승용차, 경트럭, 스포츠유틸리티차량(SUV) 및 미니밴. 이러한 안전벨트 어셈블리의 버클 베이스는 열처리가 제대로 되지 않아, 연방 자동차 안전 기준 제209호 "안전벨트 어셈블리"의 하중 지지 요건을 충족하지 못합니다.
차량 설명: 미끄럼 방지 제동 장치(ABS)가 장착되지 않은 승용차. 도로의 제빙 또는 먼지 억제를 위해 염화물 화합물을 사용하는 지역에서 운행할 경우, 후륜 브레이크의 압력 감지 감압 밸브(PCRV)가 부식되어 오작동을 일으킬 수 있습니다.
Vehicle description: Passenger vehicles. The air bag sensor wiring pigtail insulation can become brittle and crack over time due to accumulation of water in the pigtail protective convolute in combination with high underhood temperatures related to the routing of the wiring pigtail near the radiator. This can result in environmental stress cracking of the insulation.
Vehicle description: Passenger vehicles. The accelerator cable may have been manufactured with a burr on or near the end of the cable sleeve interior. This burr could fray the core wire resulting in the accelerator not returning to idle when the accelerator is released.
Vehicle description: Passenger vehicles. The terminals at the headlight switch and wiring harness connector can experience heat damage as a result of overheating.
Vehicle description: Passenger vehicles built with automatic transmissions which utilize a park/lock solenoid. It is possible to rotate the ignition key to the lock position and remove the key without the shift lever and transmission being in park. These vehicles do not comply with the requirements of fmvss no. 114, "theft protection."
Certain vehicles do not comply with CMVSS 205 - glazing materials. The windshields on were produced without the "AS1" mark as required by American National Standards Institute (ANSI) Z26.1. These windshields fully meet all of the requirements of Standard 205. Correction: Since the absence of the AS1 mark is highly unlikely to produce any risk of injury, no corrective action will be taken.
Certain vehicles may not comply with CMVSS 1105 - evaporative emissions. The rear fuel lines may allow fuel to seep and evaporate at the metal line to nylon tube joint at the rear of the vehicle near the fuel filter. This may cause evaporative emissions in excess of the standard. Correction: Vehicle will be inspected for signs of fuel escaping a joint between a nylon tube and a metal fuel line. If wetness or fuel odor are detected a reinforcement kit will be installed.
On certain vehicles, the floor shift automatic transmission control may be damaged if subjected to certain vehicle interior cleaning products. If exposed to these products, the transmission gear position indicator may deteriorate and not correctly indicate the actual gear position. If this occurs, the shifter will continue to operate normally, but there is the potential for incorrect gear selection. Correction: Automatic transmission floor shift control will be replaced.
Vehicle description: Passenger vehicles. The floor shift automatic transmission control can be damaged if subjected to certain interior cleaning products. The gear position indicator can deteriorate and not correctly indicate the actual gear position.
Note: Vehicles equipped with 2.5 litre engines. These vehicles may not comply with c.M.V.S.S. 1103 - exhaust emissions. Premature failure of the catalyst substrate material in the catalyst and exhaust manifold assemblies (light-off catalysts) can result in restricted exhaust gas flow, loss of power and exhaust emission levels in excess of those specified in the standard. Correction: Left and right hand light-off catalysts will be replaced. Underbody catalyst will be inspected and replaced if necessary.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).