공지
위 모델 항목에 나열된 일부 차량에서 시동 불가(크랭크 없음/시동 없음) 현상이 나타날 수 있으며, 고객이 차량을 시동할 수 없습니다. 계기판 클러스터(IPC)에 "No Key Detected(키 감지되지 않음)" 메시지가 표시될 수 있고, 백업 슬롯에서는 어떤 키 페어도 작동하지 않습니다. 원격 키리스 엔트리(RKE) 기능은 차량 잠금/잠금 해제에 정상적으로 작동합니다.
🔔 무료 계정을 만들고 Ford 익스플로러 (모든 세대) 이메일 알림 받기
기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.
위 모델 항목에 나열된 일부 차량에서 시동 불가(크랭크 없음/시동 없음) 현상이 나타날 수 있으며, 고객이 차량을 시동할 수 없습니다. 계기판 클러스터(IPC)에 "No Key Detected(키 감지되지 않음)" 메시지가 표시될 수 있고, 백업 슬롯에서는 어떤 키 페어도 작동하지 않습니다. 원격 키리스 엔트리(RKE) 기능은 차량 잠금/잠금 해제에 정상적으로 작동합니다.
Quality improvements include: -Addresses a potential false coolant head temperature DTC that triggers an engine warning light
"Quality improvements include: -Addresses a potential false coolant head temperature DTC that triggers an engine warning light"
Some 2022 Explorer vehicles equipped with a 3.3L full hybrid electric vehicle (FHEV) engine and built on 12-Jul-2022 and through 31-Oct-2022 may exhibit a coolant leak at the high voltage (HV) battery coolant cooler outlet hose. This may be due to the HV battery coolant cooler outlet hose contacting the bottom pulley of the accessory drive belt tensioner. To correct the condition, follow the Service Procedure to replace the damaged hose and install a cable tie.
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level using the Integrated Diagnostic System (IDS). Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
Ford Motor Company has determined certain 2020 Model Year Ford F-150, F-Super Duty and Explorer vehicles with a Ford factory-installed backup camera fail to conform to Federal Motor Vehicle Safety Standard number 111 - Rear Visibility. Contact your local Ford dealer to schedule a service date to perform the recall. Refer to the included communication from Ford for additional information. Altec is not able to complete this repair. All work must be completed by an authorized Ford dealer.
Some 2020 Explorer Base vehicles equipped with blind spot information system (BLIS) and class III trailer tow package 52T may exhibit an illuminated BLIS indicator and/or inability to turn the BLIS system off. This may be due to the software in the instrument panel cluster (IPC). To correct the condition, perform a programmable module installation (PMI) on the IPC using the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
Some 2017-2020 Model year vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
Some 2020 Ford and Lincoln vehicles may exhibit a symptom of no ability to schedule a remote start event using the FordPass or Lincolnway app. If only the scheduling portion of the remote start system is not functioning, please ensure that the latest level of SYNC software has been installed. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from FordPass or Lincolnway application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.
Some 2020 Explorer, Aviator, Ecosport, Mustang, Escape or Corsair may have a symptom of no ability to schedule a remote start event using the Fordpass or Lincolnway app. This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module utilizing section 415 of the workshop manual. If no update is available or the problem persists after programming, verify that the Fordpass or Lincolnway app is activated properly as per the owners guide. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2018 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Ford: 일부 2010년형 모델에서는 엔진 덜컹거림(rattle), 고장 표시등 점등, 출력 부족, 시동 불가, 거친 공회전 등 여러 증상이 나타날 수 있습니다. *rm 8/9/11 업데이트. *pe
No start with instrument cluster inoperative. *tt
Delayed crank with no start, diagnostic trouble codes (dtc) u0300/p0606/p2105/p2107, malfunction indicator module (mil) and wrench light on. *mj
An intermittent no start and/or malfunction indicator lamp (mil) on with diagnostic trouble codes (dtc's) p1233, p1234, p1235, p1236, p1237 or p1238. *tt
Subject regarding cigar lighter revised installation procedures. *tt
Some vehicles may exhibit driveability conditions and / or check engine lamp illuminated with a diagnostic trouble p0455 (gross leak detected). *tt
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).