무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

GMCGMC Envoy

1998–2009 · 2 세대 · 결함 27건 · 1개 시장
세대

기술 서비스 공지(TSB)는 제조사가 알려진 문제에 대해 딜러에게 보내는 수리 지침입니다. 안전 리콜은 아니지만 결함을 확인해 주는 경우가 많습니다.

연식
시장전체NA
Envoy II · 2002–2009
공지보통전장NA

공지

이 예비 정보 통신은 간헐적으로 크랭크가 걸리지 않거나 시동이 걸리지 않거나 시동이 걸리지 않으며 보안등이 켜지는 차량에 대한 정보를 기술자에게 제공합니다. 기술자는 진단 문제 코드 B3055, B3을 발견할 수 있습니다

NHTSA · 제조사 공지11039894연식 2007자동 번역 · 원문: 영어자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

이 예비 정보 통신은 간헐적으로 크랭크가 켜지지 않거나 시동이 걸리지 않거나 시동이 걸리지 않는 차량에 대해 기술자에게 정보를 제공합니다. 기술자는 진단 문제 코드 B3055, B3060, B3935, C0750, C0755, C0760, C0765 및/또는 C0775를 발견할 수 있습니다.

NHTSA · 제조사 공지11021792연식 2007자동 번역 · 원문: 영어자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · 제조사 공지10232136연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

NHTSA · 제조사 공지10219266연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

NHTSA · 제조사 공지10200151연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · 제조사 공지10114954연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

NHTSA · 제조사 공지10114746연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 제조사 공지10114354연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

10054E - Special Coverage (customer co-pay discontinued). The contacts on the fuel level sensor may wear prematurely. This wear could cause the fuel gauge to read empty after filling the tank and cause the malfunction indicator light (MIL) to illuminate. As the fuel level in the tank drops, the MIL may turn off and the gauge may display a reading; however, the reading may indicate a slightly higher level of fuel than what is in the tank. Eventually, as the contacts continue to wear, the fuel gauge will stop working and the MIL will illuminate continuously. If the condition occurs within the stated terms, dealers will install a new design fuel level sensor.

NHTSA · 제조사 공지10114183연식 2005–2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

NHTSA · 제조사 공지10113418연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 제조사 공지10113177연식 2004원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 제조사 공지10113120연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 제조사 공지10112697연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.

NHTSA · 제조사 공지10112436연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

NHTSA · 제조사 공지10111927연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

NHTSA · 제조사 공지10111737연식 2004원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

Diagnostic information on engine oil leak from rear of crankshaft. *tt 05-06-01*022 supplement - crankshaft oil leak repair instrumentions. *tt

NHTSA · 제조사 공지10017385연식 2005원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

Service engine soon light due a diagnostic trouble code p0606 diagnostic trouble code, operate in reduced engine power mode, and potentially stall. *tt

NHTSA · 제조사 공지10017230연식 2004원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지보통전장NA

공지

Concerns with no start, turn/hazard, interior lamps, driver information center (dic), radio, theft alarm, wipers, cruise, shift interlock, horn and/or key in signal inoperative. *tt

NHTSA · 제조사 공지628833연식 2002원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

이 서비스 공보는 냉간 방치(cold soak) 후 시동을 걸었을 때 일부 차량이 P(주차) 위치에 놓인 상태에서 앞뒤로 약간 흔들리거나 움직일 수 있음을 알려줍니다. 이 현상은 덜컥하는 소리(clunk)를 동반할 수도 있습니다. 이는 미세한 움직임으로, 차량 외부에서 볼 때 운전자가 체감하기보다는 육안으로 더 쉽게 관찰되며, 장착된 경우 자동 시동 기능을 사용할 때 나타납니다.

NHTSA · 제조사 공지11009088연식 2007자동 번역 · 원문: 영어자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

Vehicle Wide Programming(VWP)은 GM 차량의 소프트웨어를 업데이트하기 위한 새로운 절차입니다. Techline Connect에서 한 번의 선택으로 먼저 업데이트가 필요한 모듈을 식별한 다음(일부 예외 제외), 영향을 받는 모듈의 업데이트를 진행할 수 있습니다. 모듈 업데이트는 기술자가 모듈을 하나씩 업데이트할 필요 없이 병렬로 완료됩니다. 이를 통해 딜러와 고객 모두에게 보다 간소화된 방식이 제공됩니다.

NHTSA · 제조사 공지11006621연식 2006자동 번역 · 원문: 영어자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

이 게시물은 새로운 General Motors 교체용 체결 부품(전도성 마감 처리)을 사용한 전기 접지 수리에 관한 정보를 제공합니다.

NHTSA · 제조사 공지10252735연식 2006자동 번역 · 원문: 영어자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

NHTSA · 제조사 공지10249011연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

Programming And Activation Of Replacement OnStar Modules.

NHTSA · 제조사 공지10246951연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Envoy II · 2002–2009
공지경미전장NA

공지

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

NHTSA · 제조사 공지10237387연식 2007원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).