Certain light duty pickup trucks and sport utility vehicles fail to conform to federal motor vehicle safety standard no. 209, "seat belt assemblies." one of the two sensors in the driver's and front passenger's seat belt retractors could be inoperative. The seat belt retractors will lock when the belt webbing is extracted during a crash; however, the mechanism that locks the seat belt retractor when the vehicle decelerates quickly, such as heavy braking, may not operate as intended.
NHTSA · 미국2004년 4월 28일04V201000연식 2002원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
On certain mini vans, passenger and sport utility vehicles, some of these vehicles have a driver's side air bag that may not deploy as designed. In addition, the air bag inflator could rupture.
NHTSA · 미국2003년 2월 14일03V051000연식 2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Certain vehicles originally built with cloth seats that were equipped with an automatic air bag passenger sensing system and later reupholstered with aftermarket leather seat cover kits are involved. Testing has indicated that the aftermarket leather seat covers can cause the passenger sensing system to malfunction.
NHTSA · 미국2006년 10월 31일06V417000연식 2005–2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Certain sport utility vehicles were built with a driver's seat belt buckle assembly that contains an energy-absorbing loop. Sustained loads of sufficient magnitude and duration on the belt in severe crashes could fully deploy the buckle energy-absorbing loop, introducing a total of 10 additional inches of webbing into the seat belt system. The free falling latch plate used in this system may allow webbing to dynamically distribute between the lap and shoulder belt as the driver's position changes during a multiple rollover event.
NHTSA · 미국2003년 3월 31일03V117000연식 1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Vehicle description: Passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with trw seat belt buckle assemblies. The buckle base of these seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of federal motor vehicle safety standard no. 209, "seat belt assemblies."
NHTSA · 미국2000년 8월 7일00V228003연식 2000–2001원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
On certain vehicles, the driver's and/or passenger's front outboard seat-belt webbing could separate during a frontal impact having at least the same dynamics as a 48 kph frontal barrier collision. If a separation occurred and there were secondary crash events or rollover, there would be no restraint of the occupant and increased injuries could occur. Correction: A protector cover will be installed over the recliner mechanism.
캐나다 교통부1997년 9월 8일1997152연식 1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Vehicle description: Extended cab pickup trucks equipped with 60/40 front bench seats and extended cab pickup trucks and 2-door utility vehicles equipped with manual locking recliner bucket seats. The outboard safety belt webbing on the driver's and/or passenger's seat can separate during a frontal impact.
NHTSA · 미국1997년 6월 12일97V096001연식 1997원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Certain minivans, passenger and sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 225, "child restraint anchorage system." the owner's manual does not explain the meaning of the location symbols for the child restraint lower universal anchorage system.
NHTSA · 미국2003년 7월 15일03V250000연식 2002–2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).