무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Hyundai 엑셀

1985–1994 · 2 세대 · 결함 28건 · 3개 시장
세대
연식
시장전체NA
엑셀 I · 1985–1990
엑셀 I · 1985–1990엑셀 II · 1989–1994
리콜심각엔진NA

연료 계통, 가솔린

차량들이 FMVSS 301 "연료 계통 완전성" 측면 이동 장벽 충돌 시험 요건에 불합격했습니다. 연료 탱크에서의 연료 누출량이 허용 최대 유출량을 초과했습니다.

NHTSA · 미국1993년 11월 23일93V192000연식 1990–1994자동 번역 · 원문: 영어자세히 보기 →
엑셀 I · 1985–1990
리콜심각엔진NA

Engine

Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.

캐나다 교통부1991년 12월 30일1991176연식 1988–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
엑셀 I · 1985–1990
리콜심각엔진NA

Fuel System

The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086

캐나다 교통부1986년 4월 18일1986044연식 1986원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 II · 1989–1994
리콜보통전장NA

전기 시스템: 교류발전기/발전기/전압조정기

일부 차량에서는 전자식 크랭크 각 센서의 제조사 보호용 내부 코팅이 사양을 충족하지 않아, 고온 작동 시 회로가 개방(단선)될 수 있습니다. 이로 인해 차량이 시동 꺼짐(엔진 정지)을 일으킬 수 있습니다.

NHTSA · 미국1994년 5월 11일94V090000연식 1994자동 번역 · 원문: 영어자세히 보기 →
엑셀 I · 1985–1990
리콜보통변속기NA

Power train:Manual transmission

The manual transmissions may lock up from insufficient lubrication of the gears in the transmission case. This can cause the drive wheels to seize and the vehicle to come to a sudden stop.

NHTSA · 미국1993년 10월 4일93V167000연식 1986–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통엔진NA

Engine and engine cooling:Exhaust system

Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.

NHTSA · 미국1991년 12월 31일91V225000연식 1986–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통서스펜션NA

Suspension

The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.

캐나다 교통부1990년 5월 18일1990072연식 1990원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통서스펜션NA

Wheels:Hubcap/cover

Lock washer located under the nut that secures the front hub to the drive shaft may have had improper heat treatment and could crack.

NHTSA · 미국1990년 3월 15일90V053000연식 1990원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통브레이크NA

Brakes

The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.

캐나다 교통부1987년 11월 27일1987127연식 1986–1987원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통브레이크NA

리콜

The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.

캐나다 교통부1986년 3월 29일1986033연식 1986원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜보통브레이크NA

Service brakes, hydraulic:Pedals and linkages

A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.

NHTSA · 미국1986년 3월 17일86V043000연식 1986원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
엑셀 I · 1985–1990
리콜경미전장NA

Vehicle speed control

If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.

NHTSA · 미국1989년 6월 19일89V100000연식 1986–1989원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).