This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.
NHTSA · 제조사 공지11034436연식 2020원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.
NHTSA · 제조사 공지10185957연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
NHTSA · 제조사 공지10165350연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.
NHTSA · 제조사 공지10120369연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.
NHTSA · 제조사 공지10118478연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear: 1) Lane Departure Warning System (LDWS) warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. 2) High Beam Control (HBC) System warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear).
NHTSA · 제조사 공지10118126연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".
NHTSA · 제조사 공지11011138연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · 제조사 공지11009639연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
NHTSA · 제조사 공지11008573연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
NHTSA · 제조사 공지10254190연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control
NHTSA · 제조사 공지10252509연식 2024원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
NHTSA · 제조사 공지10240366연식 2023원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.
NHTSA · 제조사 공지10186320연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit rust (A) on the front door quarter glass guide (B) where it contacts the door beltline molding (C). The paint on the quarter glass guide gets damaged from vibration when the door is closed and when driving. This concern is caused by the beltline molding contacting the quarter glass guide due to production variances. To correct this concern, a spacer has been attached at the contact area to assure an appropriate clearance between the beltline molding and the quarter glass guide.
NHTSA · 제조사 공지10154453연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · 제조사 공지10153338연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA · 제조사 공지10153339연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.
NHTSA · 제조사 공지10153294연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit the power window(s) not working properly (window does not move or has fallen into the door) and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding.To eliminate this concern, the shape of the door glass will be modified during mass production to prevent water entry to the power window regulator.
NHTSA · 제조사 공지10153292연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA · 제조사 공지10148072연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA · 제조사 공지10148071연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.
NHTSA · 제조사 공지10144324연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Dealer Rework (DRW) 09 ? 2018 Mazda MX-5 Power Window Switch Concern: On affected vehicles, the driver power window main switch is not correctly assembled to the power window main switch door panel. There are 4 tabs (2 tabs on front side, 2 tabs on rear side) on the power window main switch affixed to the door panel. It is possible that 1 or 2 of the tabs are not locked, and there is a chance the switch will drop slightly when the power outer mirror switch is pushed.When the power window main switch part is assembled to the driver-side door trim by a jig in production, the power window main switch could have been unintentionally pushed vertically due to the jig misalignment.
NHTSA · 제조사 공지10134937연식 2018원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct this problem, the control logic of the BSM control modules has been changed.
NHTSA · 제조사 공지10120383연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit a squeak noise at the rear beltline when the door glass moves up and/or down. This concern happens especially when the door glass is wet with moisture or after a car wash. This is caused by stick-slip noise occurring at the contact surfaces between the door glass and the weather strip. With repeated moving up and down, the anti-noise paint on the weather strip peels off. To prevent the stick-slip noise, a polyester film has been attached at the applicable location of the weatherstrip.
NHTSA · 제조사 공지10120357연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).