Mazda Motor Corporation has decided to take corrective action on certain 2022MY MX-5 built in Japan from September 5th to September 8th, 2022. All vehicles in this campaign must be repaired prior to retail delivery. Concern Outline: On the subject vehicles, an abnormal noise may be heard from the rear differential when the vehicle is operating around 68 mph. The noise is caused by improper differential teeth contacting between the ring gear and drive pinion.
NHTSA · 제조사 공지10222434연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
SSPC0 - CALIFORNIA REGISTERED VEHICLES DIAGNOSTIC TROUBLE CODES (DTC) CONCERN: Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2019 CX-3, Mazda3 and MX-5 as well as 2018 Mazda6 vehicles and produced in the production date ranges below. This SSP will apply only to owners currently registered in the state of California. There are 6,715 vehicles in the VIN ranges above that are registered in the state of California. Concern Outline: On certain subject vehicles, if the vehicle sets diagnostic trouble codes (DTC) P2096 / P2097 and/or P0524, in the memory of the powertrain control module (PCM), they cannot be cleared even after the concern that created the DTC has been resolved.
NHTSA · 제조사 공지10177975연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA · 제조사 공지10159204연식 2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status Monitor/Maintenance reset menu. The wrench light (Oil Change Due message) is displayed before the oil change is due. Vehicles with multi-information display Vehicles without multi-information display This is caused by only one reset procedure being performed when the oil is changed, usually using the center display. Two reset procedures are required, one is using the trip meter switch to reset the powertrain control module (PCM) and the other is using the center display to reset the connectivity master unit (CMU). To correct this issue, the CMU software has been modified so that the oil maintenance monitor reset operation on the center display resets both the CMU and the PCM at the same time. With this change, there set operation using the trip meter switch is now unnecessary.
NHTSA · 제조사 공지10148073연식 2018–2019원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Some vehicles may exhibit a creak noise from around the rear differential when the clutch is engaged quickly or the vehicle accelerates/decelerates rapidly. This is caused by a stick-slip noise occurring at the contact surface between the power plant frame (ppf) (a) and the rear differential. To eliminate this concern, the tightening torque of the stud bolts and nuts has been increased.
NHTSA · 제조사 공지10092535연식 2016원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
Subject on transmission control module( tcm ) protector pad application. *yc
NHTSA · 제조사 공지603121연식 1999원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).