무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mercedes-BenzMercedes-Benz CLS 클래스 C219

2003–2010 · 결함 17건 · 3개 시장

이 파일은 Mercedes-Benz CLS 클래스 C219의 알려진 결함을 커뮤니티가 출처와 함께 정리한 것입니다. 누구나 무료로 읽을 수 있고, 무료 계정으로 기여할 수 있습니다. 신뢰할 수 있는 기여자가 충분히 검증하면 결함에 인증 마크가 붙습니다.

소유자들이 이 차의 fuel system 문제를 자주 보고하지만(88건) 아직 아무도 원인을 설명하지 않았습니다. 알고 계신가요?항목 작성
소유자들이 이 차의 brakes 문제를 자주 보고하지만(33건) 아직 아무도 원인을 설명하지 않았습니다. 알고 계신가요?항목 작성

가장 심각한 결함

전체 보기 (17) →
m
심각변속기NA

Transmission and drivetrain: problems reported by owners

14 owners in the United States reported problems with the transmission and drivetrain of this car to NHTSA (model years 2006–2009), typically at around 34,000 miles. Most often named: automatic transmission (43%). Reported consequences: 5 injuries.

✓ 공식 데이터에 대한 Mecafile 분석2006–2009원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
m
심각실내NA

Airbags: problems reported by owners

13 owners in the United States reported problems with the airbags of this car to NHTSA (model years 2006–2009), typically at around 83,000 miles. Most often named: frontal (15%). Reported consequences: 5 crashes, 6 injuries.

✓ 공식 데이터에 대한 Mecafile 분석2006–2009원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
m
심각전장NA

Electrical system: problems reported by owners

12 owners in the United States reported problems with the electrical system of this car to NHTSA (model years 2006–2009), typically at around 50,000 miles. Reported consequences: 1 fire.

✓ 공식 데이터에 대한 Mecafile 분석2006–2009원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

최신 공식 리콜

전체 보기 (40) →
리콜보통서스펜션EU

스티어링 박스의 알루미늄 나사 3개는 물보라와 부식성 물질(…)에 노출되면서 부식될 수 있습니다.

스티어링 박스의 알루미늄 나사 3개는 분사되는 물과 빙판을 녹이기 위해 사용되는 공격적인 도로 제설재(염화물)에 노출되어 부식될 수 있습니다. 부식이 심해지면 나사가 약해져 기동이나 주차 중에 파손될 수 있습니다. 고정 나사가 모두 파손되면 파워 어시스트 스티어링이 분리될 수 있으며, 이로 인해 파워 스티어링 기능을 잃고 사고 위험이 높아질 수 있습니다.

Safety Gate · EU2024년 12월 17일SR/03711/24연식 2010자동 번역 · 원문: 영어자세히 보기 →
리콜보통차체NA

Visibility:Sun/moon roof assembly

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2001-2011 C-Class, CLK, E-Class, and CLS vehicles. Please see the recall report for a complete list of models and model years. The glass sunroof panel may not be properly secured and can detach.

NHTSA · 미국2024년 11월 19일24V874000연식 2006–2010원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
리콜보통차체JP

車体

スライディングルーフのガラスパネルにおいて、製造管理が不適切なため、接着強度が不十分なものがある。そのため、ガラスパネルに浮きが発生し、最悪の場合、走行風により脱落して、後続車両の妨げになるおそれがある。

국토교통성 · 일본2023년 6월 22일1236290연식 2002–2010원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →

최신 기술 서비스 공지

전체 보기 (106) →
공지경미차체NA

공지

**고객 불만:** 도어 내 스피커 부근에서 덜컹거리는 소음이 발생함. **원인:** 분석 중. **조치:** 원인을 좁히기 위해 먼저 도어 트림을 분리하십시오. 도어 트림을 분리한 상태에서도 소음이 계속 발생하면 스피커 쪽으로 진단을 계속 진행하고, 필요한 경우 유용한 동영상을 첨부하여 TIPS 케이스를 생성하십시오. **참고:** 보증 클레임에서 이 문서를 참조하고, 진단이 완료되면 문제를 일으키는 부품에 따라 손상 코드를 선택하십시오. 도어 트림을 분리했을 때 소음이 멈추면 LI72.10P067691에 따라 진행하십시오. **정보:** 이 경우 보증 클레임에서 스피커에 대한 손상 코드를 사용하지 마십시오!

NHTSA · 제조사 공지11038217연식 2006자동 번역 · 원문: 영어자세히 보기 →
공지보통브레이크NA

공지

**고객 불만** 60MPH에서 제동 시 차량 진동이 발생하여 재방문 정비를 받음. 참고: 증상이 타이어나 휠 진동과 유사하더라도, 항상 발생하는지 아니면 제동 시에만 발생하는지에 따라 뚜렷하게 구별되는 경우가 많습니다. **원인** 진동의 원인은 대개 로터 또는 허브/휠 베어링의 과도한 측면 런아웃일 가능성이 높습니다. 그러나 다른 가능한 원인이 있는지 전체 시스템을 함께 점검해야 합니다. 1. 이전 충돌로 인한 손상 2. 회전 부품 없이 차량을 장기간 방치한 경우 3. 휠 베어링/허브의 측면 런아웃 4. 휠 결합면이 과도하게 조여진 경우(WIS 토크 절차를 따르지 않음) 5. 결합면이 과도하게 개조된 경우(도장, 긁힘, 휨 등) **조치 방법** 작업을 수행하기 전에 첨부된 작업 시트 전체를 읽어 보십시오. 작업 후에는 마지막 페이지를 검토하고 그에 따라 작업하십시오. 참고: 이 문서는 사전 승인이 아니며 보증과 관련된 문서도 아닙니다. 진단 목적으로만 사용됩니다. 진행 방법에 대해 의문이 있거나, 작업 시트를 수행했음에도 같은 증상으로 차량이 다시 입고된 경우에는 작업 시트에 나온 측정을 다시 수행한 후, Body, Chassis, and Entertainment 팀에 TIPS 케이스를 등록하십시오.

NHTSA · 제조사 공지11038186연식 2006자동 번역 · 원문: 영어자세히 보기 →
공지보통브레이크NA

공지

Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy The intent of this document is to reduce noise from high performance AMG brakes. AMG brakes are designed for performance under high load and in certain scenarios, can emit noise. Some scenarios are normal and some are induced by driving style like those listed below: Driving style such as two footed driving where the pad might be in constant contact with the rotor. Brake pressure and application style (stopandgo traffic with consistent light brake pressure riding brakes where the brakes cannot cool sufficiently between applications). This can cause the brake pads to glaze and have a smooth/glassy surface which can induce noise. When ambient temperatures rise during summer peak and during cooling and cold winter months. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 34 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to reassessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. Continue with applying chamfer and Molykote as instructed below. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! a) If the noises are coming from the front axle. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining backing plate, including the brake lining guide pins and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Be sure to remove both brown paper backing sides of the adhesive film, it is double sided adhesive film. 5. If adhesive is already installed on backing plate where pistons contact the back of the pad, you may gently scrape off and reapply a new adhesive or Molykote. Must not apply the Molykote on top of the adhesive. 6. Chamfer edges (gently round off sharp leading edges) on brake pads. Some pads have vertical grooves, these can be gently chamfered with a triangular file as well. See picture "Chamfering Technique". 7. Apply Molykote to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 8. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle. 1. Remove brake pads of rear axle. 2. Clean all contact points on brake lining backing plate and brake caliper /carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the pistonside brake lining. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfering Technique". 5. Grease contact points (red areas on attachment "Rear Pad Grease Area") between brake lining and guide of brake caliper with Molykote. 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off

NHTSA · 제조사 공지11037487연식 2006원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).