무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Mercedes-BenzMercedes-Benz EQA

2021–2026 · 1 세대 · 결함 1건 · 3개 시장
세대
모든 세대EQA2021–202612313

Mercedes-Benz EQA의 모든 세대를 한곳에: 결함, 리콜, 서비스 회보, 토론. 세대를 선택해 범위를 좁히세요.

가장 심각한 결함

전체 보기 (1) →

최신 공식 리콜

전체 보기 (23) →
리콜보통전장EU

Le boîtier de pyrofuse peut se déplacer pendant que le véhicule est en mouvement, ce qui peut endommager…

Le boîtier de pyrofuse peut se déplacer pendant que le véhicule est en mouvement, ce qui peut endommager les câbles. en conséquence, le pyrofuse pourrait tomber en panne lors d’un accident ou faire déloger le piston du séparateur dans le repose-pied du conducteur, ce qui augmenterait le risque de blessure. en outre, dans les véhicules hybrides et électriques rechargeables, les dommages aux câbles pourraient entraîner une défaillance du système à haute tension et une perte d'énergie sans avertissement, ce qui augmenterait le risque d'accident.

Safety Gate · EU · RappelConso · 프랑스2026년 6월 26일a12/02969/24연식 2024원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →
리콜심각전장JP

バッテリー

EV車両のバッテリにおいて、製造管理が不適切なため、充電率が高い状態においてバッテリのセル内で短絡が発生することがある。そのため、走行中に警告メッセージが表示されることがあるほか、最悪の場合、火災に至るおそれがある。

jp2026년 3월 26일1241310연식 2023–2024원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →

최신 기술 서비스 공지

전체 보기 (13) →
공지보통서스펜션NA

공지

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

NHTSA · 제조사 공지11018204연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통서스펜션NA

공지

Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Test: Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Reset the HOSWD control unit in line with the guided test in Xentry. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> replace steering wheel rim. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no defect is visible: Please do not replace the steering wheel, but wait for new coding parameters which should be available 05/2025. Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. B1E7713: Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is now available for Star 3 vehicles only. Fault in IDC223 control unit: U186B29: Delete fault memory and flash the new IDC (N62/4) software A223 902 75 37. If the software update is not available, or the problem persists, create a TIPS case. Fault in IDC213 control unit: U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the HOSWD control unit then scan the steering wheel and check whether the fault is reproducible. If reproducible: Create a TIPS case, adding the

NHTSA · 제조사 공지11017516연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
공지보통전장NA

공지

Complaint The message "Device detected at diagnostics connection See Owners Manual" appears sporadically in the multifunction display of the instrument cluster while driving (see picture in attachment). Cause On vehicles with HERMES 3.0 currently, A2389015700 A2389015800 A2389018400 A2389018900 A2389019000 A2389019800 A2579011200 A2579012100 The above-mentioned message is sporadically displayed in the instrument cluster once Remedy Please manually commission the control unit N112/9 (HERMES) using XENTRY: XENTRY "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit" Invoice the required work using damage code 8251M/01 (damage location/damage type).

NHTSA · 제조사 공지11017135연식 2021원문(영어)으로 표시 중 · 번역 대기자세히 보기 →

최신 포럼 글

아직 토론이 없습니다.

결함과 토론은 세대별로 정리됩니다. 글을 올리려면 위에서 세대를 선택하세요.

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0).