무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

Nissan 쥬크

2010– · 3 세대 · 결함 21건 · 5개 시장
세대
연식
쥬크 I · 2010–2019
리콜심각실내EU

En raison d’une erreur dans le processus de pliage du coussin gonflable du conducteur, le bouclier…

En raison d’une erreur dans le processus de pliage du coussin gonflable du conducteur, le bouclier thermique peut ne pas se déplacer complètement autour du gonfleur lorsque l’airbag est activé. par conséquent, le gaz chaud peut directement entrer en contact avec le panneau avant de l’airbag, causant des dommages de brûlure au matériau du sac. en conséquence, l’airbag peut se déchirer pendant l’inflation réduisant sa fonction protectrice.

Safety Gate · EU · RappelConso · 프랑스2021년 3월 26일a12/00391/21연식 2019원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각실내JP

始動装置

イグニッションスイッチのポジション保持用スプリングにおいて、成形設備のメンテナンスが不適切なため、成形時に傷がついたものがある。そのため、イグニッションキー操作の繰り返しによって当該スプリングが破損し、イグニッションキーに多数のキーホルダー等の重量物を装着していると、走行中の振動等によりイグニッションキーがON位置以外に回転し、車両電源が断たれてエンジンが停止するおそれがある。なお、この状態で事故を起こした場合、エアバッグが展開しない。

국토교통성 · 일본2018년 9월 6일1143180연식 2016–2018원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진EU

An internal ignition switch may be defective

An internal ignition switch may be defective. As a consequence, the engine could unexpectedly stall while driving and under certain conditions the vehicle's airbag system may not function.

Safety Gate · EU2018년 8월 29일A12/1281/18연식 2017원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel System

On certain vehicles, the fuel pressure sensor may not have been tightened properly when the corrective measure of recall 2012-074 was performed. As a result, the fuel pressure sensor may loosen over time, which could cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and retighten the fuel pressure sensor as necessary.

캐나다 교통부2018년 3월 8일2018121연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain 2011-2012 Nissan Juke vehicles previously remedied under recall 12V-069. During that recall remedy, the fuel pressure sensor may not have been properly tightened, potentially causing the sensor to loosen and leak fuel.

NHTSA · 미국2018년 3월 7일18V156000연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각브레이크JP

圧力制御伝達部

ブレーキマスターシリンダにおいて、倍力装置内部のスプリングの製造のバラツキを考慮した設計をしていなかったため、ピストンが傾いて押されカップシールとの摺動抵抗が高くなり、ブレーキペダルを速く踏みこんだ際にカップシールが捲れることがある。そのため、シール部から倍力装置内部にブレーキ液が漏れ、そのままの状態で使用を続けると警告灯が点灯し、最悪の場合、制動力が低下して制動距離が長くなるおそれがある。

국토교통성 · 일본2018년 2월 1일1141890연식 2015–2017원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각전장NA

Electrical

On certain vehicles, due to a manufacturing defect the start/stop button could stick inside of its housing. If this occurs, vibration could cause the electrical components inside the button to contact repeatedly in quick succession and initiate the emergency engine shut off procedure while the vehicle is in motion. This could result in increased steering and braking effort, a loss of motive power and would disable the supplemental restraint systems (SRS), increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair defective start/stop switch as necessary.

캐나다 교통부2015년 6월 25일2015282연식 2013–2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진EU

Motorrijtuigen - krachtoverbrenging

Brandstofdruksensor niet correct vastgezet. Hierdoor kan de sensor onder invloed van warmte en trillingen losraken.

rdw2015년 3월 23일MGP150107연식 2012–2013원문(네덜란드어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각전장EU

null The fuel rail pressure sensor of some vehicles may be tightened insufficiently to the fuel rail of…

null The fuel rail pressure sensor of some vehicles may be tightened insufficiently to the fuel rail of the engine and it may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition, in an extreme case, fuel leakage may occur between the fuel rail pressure sensor and the fuel rail.

Safety Gate · EU2014년 12월 5일A12/1975/14연식 2012–2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and the rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect the pressure sensor and tighten to specification. Note: This is an expansion of recall 2012-074. Vehicles that were repaired under the previous campaign are not affected because that remedy would have corrected the subject condition.

캐나다 교통부2014년 11월 28일2014539연식 2011–2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel system, gasoline

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2014 Nissan Juke, 2012-2013 Infiniti M56, QX56, and 2014-2015 Infiniti Q70 (V8 engine vehicles only), and QX80 vehicles. The fuel pressure sensors may not have been sufficiently tightened during production. As a result, the fuel pressure sensor may loosen with vehicle usage and cause a fuel leak.

NHTSA · 미국2014년 11월 28일14V683000연식 2012–2014원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진JP

その他(燃料装置)

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不適切なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

국토교통성 · 일본2014년 11월 27일1134761연식 2010–2014원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
쥬크 I · 2010–2019
리콜심각실내UK

Airbag may release high temperature gases

In the event that the driver airbag is deployed during a frontal impact small holes may occur on the surface of the airbag. The holes are caused by high temperature gases from the airbag inflator exhausting directly onto the surface of the airbag material. The high temperature gas/airbag material may contact the drivers skin. The deployment performance of the driver airbag is not affected.

DVSA · 영국2013년 2월 25일R/2013/019연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각실내EU

null In the event that the driver's airbag is deployed during a frontal impact, small holes may appear on…

null In the event that the driver's airbag is deployed during a frontal impact, small holes may appear on the surface of the airbag. The holes are caused by high temperature gas from the airbag inflator exhausting directly onto the surface of the airbag material. Contact of the high temperature gas / airbag material with the driver’s skin can cause burns.

Safety Gate · EU2013년 2월 20일A12/0243/13연식 2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진UK

Fuel may leak

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

DVSA · 영국2012년 4월 3일R/2012/024연식 2010–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel system, gasoline

Nissan is recalling certain model year 2011-2012 juke, infiniti qx and infiniti m vehicles. The fuel pressure sensors may not have been tightened to the correct specification. As a result, the fuel pressure sensor may loosen due to heat and vibration causing fuel to leak.

NHTSA · 미국2012년 2월 24일12V069000연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각전장JP

コモンレール

エンジンの燃料供給レールに取り付けている燃料圧力センサの締付けが不充分なため、エンジンの振動等により締付けが緩むものがある。そのため、燃料圧力センサの取付け部のねじを伝って燃料が漏れるおそれがある。

국토교통성 · 일본2012년 2월 23일1128970연식 2010–2011원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019
리콜심각엔진NA

Fuel System

On certain vehicles, the fuel pressure sensor connected to the engine fuel delivery rail may not have been sufficiently tightened during vehicle assembly. Should the pressure sensor loosen, fuel could leak past a gasket used in the connection between the sensor and rail. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will inspect for fuel leakage from the pressure sensor and the fuel rail. If there are no signs of a fuel leak, the fuel pressure sensor will be tightened to specifications. If a fuel leak is confirmed, the gasket between the sensor and the fuel delivery rail will be replaced, and the sensor will be tightened.

캐나다 교통부2012년 2월 23일2012074연식 2011–2012원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 II · 2019–
리콜보통실내UK

Juke (F16) 앞좌석 안전벨트

차량 일부에서 조립 전 부품 준비 과정 중 앞좌석 안전벨트가 실수로 손상되었을 가능성이 있습니다.

DVSA · 영국2025년 4월 7일R/2025/118연식 2024자동 번역 · 원문: 영어자세히 보기 →
쥬크 I · 2010–2019쥬크 II · 2019–
리콜보통기타UK

Juke (F16) Qashqai (J12) 및 Leaf (ZE1) VIN 스캔

차량 시스템에 저장된 VIN이 실제 차량의 VIN과 일치하지 않을 수 있습니다. 이로 인해 차량 사용자가 다른 차량과 관련된 정보를 볼 수 있게 되어 데이터 보안 침해가 발생할 수 있습니다.

DVSA · 영국2024년 6월 17일R/2024/234연식 2019–2023자동 번역 · 원문: 영어자세히 보기 →
쥬크 I · 2010–2019
리콜보통브레이크EU

En raison d’un changement de conception introduisant un chanfrein interne dans le bouton de verrouillage…

En raison d’un changement de conception introduisant un chanfrein interne dans le bouton de verrouillage arrière du siège arrière, la tige d’actionnement de la serrure peut attraper ce chanfrein, empêchant son mouvement vers le haut. en conséquence, le dossier du siège arrière peut ne pas être solidement verrouillé lorsqu’il est retourné à sa position verticale après pliage, et l’occupant du siège arrière et de tous les objets entreposés dans le compartiment à bagages peut ne pas être correctement retenu en cas d’accident, ce qui augmente le risque de blessure.

Safety Gate · EU · RappelConso · 프랑스2023년 8월 8일a12/01430/21연식 2019–2020원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 II · 2019–
리콜보통브레이크UK

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

DVSA · 영국2023년 4월 19일R/2023/096연식 2022원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 II · 2019–
리콜보통브레이크EU

Si l’accélérateur et les pédales de frein sont pressés simultanément, cela provoque une réinitialisation…

Si l’accélérateur et les pédales de frein sont pressés simultanément, cela provoque une réinitialisation de la commande de véhicule électrique hybride (hevc). cela peut conduire à ce que le moteur trébuche ou décroche dans des conditions de conduite spécifiques (lorsque le moteur est froid, immédiatement après le démarrage), ce qui crée un risque d’accident.

Safety Gate · EU · RappelConso · 프랑스2023년 4월 14일a12/00724/23연식 2022원문(프랑스어)으로 표시 중 · 번역 대기자세히 보기 →
쥬크 I · 2010–2019쥬크 II · 2019–
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).