Steering:Gear box (other than rack and pinion)
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
🔔 무료 계정을 만들고 Pontiac 파이어버드 (모든 세대) 이메일 알림 받기
The steering intermediate shaft could have been improperly assembled causing the shaft lower coupling to loosen and rotate on the steering gear input shaft.
These vehicles may have been built with an improperly assembled steering intermediate shaft. This condition could cause the intermediate shaft lower coupling to loosen and rotate on the steering gear input shaft. If this were to occur while the vehicle was in motion, a loss of steering control could result and a crash could occur without prior warning. Correction: Steering shaft will be inspected and lower coupling will be replaced if required.
연료 주입구 목(neck)의 납땜 접합부에 균열이나 핀홀 누출이 생길 수 있으며, 이는 FMVSS No. 301 "연료 계통 건전성(fuel system integrity)" 기준에 부합하지 않습니다. 이러한 균열과 구멍은 연료 증기와 연료 누출을 일으킬 수 있습니다.
이 차량들은 주유구 목(filler neck) 납땜 접합부에 균열 또는 "핀홀(pin hole)"이 발생할 수 있습니다. 이로 인해 연료 냄새 또는 연료 누출이 발생할 수 있습니다. 점화원이 있는 경우, 이 상태에서 발생한 연료 누출이 차량 화재로 이어질 수 있습니다. 시정 조치: 해당 차량의 연료 탱크는 누출 여부를 점검하고, 필요한 경우 교체합니다.
Note: Vehicle located in ontario. The fuel line could develop a hole due to contact with the hot air (air injection reaction) check valve. This could result in fuel leakage and an engine compartment fire. Correction: Fuel line bundle will be inspected for heat damage and replaced if necessary. Fuel line bundle will also be rerouted.
The fuel lines on these vehicles may have been misrouted and may contact the "air" check valve. The high temperatures from the "air" check valve could allow it to melt through and damage a fuel line.
Fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly.
Fuel return hoses may break at either crimped coupling.
Note: Vehicles equipped with 5.0 litre and 5.7 litre engines. Vehicles may have fuel return hoses which could break at either or both crimped couplings. If a coupling were to separate, fuel leakage and a possible engine compartment fire could result. Correction: A properly crimped fuel return hose will be installed on all involved vehicles.
Note: Vehicles equipped with 2.8.L v6 engines. The fuel feed hoses may pull out of the crimped coupling at the engine end of the hose assembly. This could result in fuel leakage and an engine compartment fire. Correction: A redesigned fuel feed hose will be installed on all involved vehicles.
The hub area of the wheels may not be structurally sound and thus subject to fracture. Consequence of defect: The wheels could separate from the car causing a loss of control. This could result in an accident without prior warning.
Due to undersized grinding at the time of manufacture, the rear brake centre flex hoses could separate from the end fittings when subjected to the pull force required by cmvss 106-74. Tensile strangth test. Such a separation would result in loss of brake fluid and a partial loss of braking action. Should this happen while the vehicle is in motion, at a time when minimum stopping distances are required, a vehicle crash could occur without prior warning.
The involved vehicles do not conform to federal motor vehicle safety standard no. 210, "seat belt assembly anchorages". The non-compliance exists because the rear seat belt anchorages may pull through the underbody of the vehicle if enough force is applied.
Fuel tank ventilator valve in the fuel system may produce a loud and persistent "whistle" during venting of the tank. If the fuel filler cap is removed while this condition exists and the tank is more than 3/4 full, gasoline may be forced out of the filler neck onto bystanders.
일부 차량에서는 뒷좌석의 안전벨트 리트랙터(retractor)에 있는 1차 잠금 위치(first lock positions)가 체구가 작은 승객이 사용할 때 잠기지 않는 문제가 있습니다. 이는 연방 자동차 안전 기준(FMVSS) 제208호 "탑승자 충돌 보호(occupant crash protection)"의 요구 사항을 충족하지 못하는 것입니다.
Vehicle description: Certain passenger vehicles fail to conform to the requirements of fmvss no. 208, "occupant crash protection," and no. 214, "side impact protection." these vehicles may have welds near the lower driver's side door hinge that do not meet specifications.
Vehicle description: Passenger vehicles equipped with manual transmissions. The clutch master cylinder may have been built with an incorrect retaining ring.
Note: Vehicles equipped with 5.7 litre engines. The exhaust gas recirculation (egr) valve could fail due to internal corrosion. This could result in the vehicle failing to meet applicable emissions requirements. Correction: Dealers will inspect the egr valve for part number and replace, if necessary, with a new design egr valve.
Note: Convertible vehicles. These vehicles do not comply with c.M.V.S.S. 209 - seat belt assemblies. The front seat belt retractors may lock-up on slopes less severe than the requirement of the standard. As a result, occupants may not be able to extract and fasten their seat belts until the vehicle is moved to a more level surface. Correction: Dealers will inspect for proper front seat belt retractor position and those found to be improperly positioned will be reinstalled correctly.
These vehicles were manufactured with seat belt retractors out of design position which can cause the retractor to lock-up on slopes less severe than the fmvss requirement. This does not comply with fmvss no. 209, "seat belt assemblies."
Note: Vehicles equipped with 4l60 automatic transmissions. The shift control cable conduit may separate and prevent the transmission from being shifted into the proper position, for example, the transmission shift lever may be in the park position when the transmission is actually in drive or reverse. This condition may cause unexpected vehicle movement and could result in a vehicle crash without prior warning. Correction: A revised shift control lever will be installed on affected vehicles.
The automatic transmission shift control cable can separate.
These vehicles may not comply with c.M.V.S.S. 209 - seat belt assemblies. - seat belt latch plates may not engage or may do so only after wiggling and/or forcing the latch plate. Correction: Vehicles will be inspected and suspect retractor side safety belt assemblies (which include latch plates) will be replaced if necessary.
The metal latchplates may not engage the buckle assemblies, causing a "no latch" condition. Movement of the seat occupant in this condition could cause latchplate release from the buckle.
차량에 따라 주차 브레이크 시스템에 제대로 작동하지 않는 주차 브레이크 조정기가 포함되어 있을 수 있습니다. 이로 인해 후륜 디스크 패드가 마모되면서 주차 브레이크의 제동력이 점차 떨어질 수 있습니다. 그 결과 경사가 가파른 곳에서는 주차 브레이크가 차량을 제대로 고정하지 못할 수 있습니다. 변속기가 중립이거나 전진 기어에 놓인 상태로 주차했을 경우 차량이 굴러가 부상이나 재산 피해로 이어질 수 있습니다. 시정 조치: 새로운 주차 브레이크 조정기가 장착됩니다.
출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).