무료 열람 · 무료 계정으로 기여Anticars(2000)의 후속

SaabSaab 9-5

1997–2011 · 2 세대 · 결함 15건 · 3개 시장
세대
연식
9-5 I · 1997–20099-5 II · 2009–2011
리콜심각실내NA

에어백

순정 차량 일부에서 운전석 전면 에어백 인플레이터가 에어백 작동 중 과도한 내부 압력을 발생시킬 수 있습니다. 압력이 높아지면 인플레이터가 파열되어 파편이 차량 탑승자 쪽으로 튀어나갈 수 있으며, 이로 인해 부상 위험이 높아질 수 있습니다. 또한 에어백 모듈이 손상되어 정상적인 전개가 방해받을 수 있습니다. 충돌 시 전개가 필요한 상황에서 에어백이 완전히 펴지지 않으면 좌석 탑승자의 신체 부상 위험이 증가할 수 있습니다. 시정 조치: 딜러는 Saab 9-3 및 9-5 차량의 운전석 에어백 인플레이터를 교체하고, Saturn Astra 차량의 운전석 에어백 모듈을 교체합니다.

캐나다 교통부2016년 2월 3일2016052연식 2006–2009자동 번역 · 원문: 영어자세히 보기 →
9-5 I · 1997–20099-5 II · 2009–2011
리콜심각실내NA

에어백:전면:운전석 측:인플레이터 모듈

General Motors LLC (GM)은 2002년 5월 31일부터 2011년 2월 15일 사이에 제작된 2006~2011년식 Saab 9-3 일부 차량, 2005년 6월 7일부터 2009년 5월 28일 사이에 제작된 2006~2009년식 Saab 9-5 일부 차량, 그리고 2007년 4월 11일부터 2008년 7월 24일 사이에 제작된 2008~2009년식 Saturn Astra 일부 차량을 리콜합니다. 운전석 정면 에어백이 작동할 때 내부 압력이 과도하게 높아져 인플레이터가 파열될 수 있습니다.

NHTSA · 미국2016년 2월 3일16V063000연식 2006–2009자동 번역 · 원문: 영어자세히 보기 →
9-5 II · 2009–2011
9-5 I · 1997–2009
리콜심각엔진UK

Fuel may leak - fire may occur

Fuel may leak from the return hose because it is not to specification and will age/crack prematurely. In the worst case fire may occur.

DVSA · 영국2009년 1월 26일R/2008/188연식 2006–2008원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각엔진JP

燃料ホース/パイプ

燃料ホースと燃料ポンプの組付けが不適切なものがあり、燃料ホース取付け部に応力がかかるものがある。そのため、そのままの状態で使用を続けると、最悪の場合、車両の振動等により当該取付け部が折損し、燃料が漏れるおそれがある。

국토교통성 · 일본2007년 5월 29일1214060연식 1999–2007원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
9-5 I · 1997–2009
리콜심각전장NA

Electrical system:Ignition:Module

Certain passenger vehicles equipped with b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.

NHTSA · 미국2006년 10월 26일06V410000연식 2002–2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각전장NA

Electrical

Certain 2000-2002 Saab 9-3 and 9-5 model vehicles equipped with 4-cylinder gasoline engines, and 2001-2003 9-5 models equipped with 6-cylinder gasoline engines may experience overheating and burnout of the Isolated Gated Bipolar Transistor (IGBT) within the Ignition Discharge Module (IDM) due to increased susceptibility to electrical loads. Overheating of the IGBT occurs most often at engine start-up but may also occur while the engine is running. When the IDM fails on a 4-cylinder while it is running, the engine may stall without warning, with no ability to be restarted. When the IDM fails on a 6-cylinder engine while it is running, the driver will initially experience reduced power and rough operation because the engine will only be running on three cylinders. The check engine light will flash. If the driver continues, unburnt fuel in the exhaust can cause thermal damage to the catalytic converter. The engine may stall and not restart. Correction: Dealers will inspect and, if required, replace the IDM.

캐나다 교통부2005년 9월 20일2005271연식 2000–2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각전장NA

Electrical system:Ignition:Module

Certain passenger vehicles equipped with b205/b235 4-cylinder gasoline engines and b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.

NHTSA · 미국2005년 9월 14일05V399000연식 2000–2002원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각서스펜션NA

Wheels:Hub

On certain passenger vehicles, if an owner changes their wheels/tires between summer and winter using a steel wheel in the winter and an alloy wheel in the summer, it is possible for rust and contamination to build up on the wheel hub during the steel wheel usage. If this occurs and the contamination is not removed, it is possible that after the tire change service, some of this contamination could flake or grind away resulting in reduced clamping force of the wheel to the hub. Over several seasons, it is possible that this reduced force could result in fractures developing in the wheel bolts due to wheel to hub movement.

NHTSA · 미국2003년 1월 13일03V006000연식 1999–2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각서스펜션NA

Steering:Linkages:Knuckle:Spindle:Arm

The steering knuckle castings on certain passenger vehicles may have been contaminated during the casting process.

NHTSA · 미국2002년 1월 4일02V006000연식 2002원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜심각엔진JP

潤滑装置

原動機において、潤滑油の油圧センサに一部製造不良のものがあり、そのままの状態で 使用を続けると、当該油圧センサに亀裂が生じ、潤滑油が漏れ、最悪の場合、火災に至る おそれがある。

국토교통성 · 일본2000년 1월 20일1207800연식 1998–1999원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통전장JP

その他(電気装置)

点火装置において、高電圧発生モジュールのトランジスタの耐久性が不足しているため、電気負荷の繰り返しによりトランジスタが破損し、原動機が停止するおそれがある。

국토교통성 · 일본2008년 7월 2일1215030연식 2002–2003원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통실내NA

Seats:Front assembly:Head restraint

Saab is recalling 57,389 my 2002-2008 9-5 series vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." during compliance testing, one of the upper interior occupant protection test points exceeded the standard's requirements.

NHTSA · 미국2008년 4월 9일08V160000연식 2002–2008원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통서스펜션JP

かじ取リンク機構

左側ナックルアームにおいて、鋳造工程が不適切なため、強度が不足しているものがある。そのため、そのままの状態で使用を続けると、当該ナックルに亀裂が生じ、最悪の場合、折損してかじ取り操作が出来なくなるおそれがある。

국토교통성 · 일본2006년 7월 21일1213220연식 2002원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통엔진JP

ブローバイ装置

ブローバイホース(クランクケースブリーザーホース)の取付け方法が不適切なため、原動機の振動等により当該ホースが外れ、ブローバイガスが大気中に放出されるおそれがある。

국토교통성 · 일본2005년 4월 15일1212180연식 2003–2004원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통차체JP

方向指示器

前面方向指示器において、灯器の取り付け方法が不適切なため、走行時の振動等により、 当該方向指示器が車体から外れるおそれがある。

국토교통성 · 일본2003년 3월 7일1210050연식 2002원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 II · 2009–2011
9-5 I · 1997–2009
리콜보통서스펜션NA

Suspension

On certain vehicles, when changing back and forth between alloy and steel wheels (as for winter tires), rust and other contaminates may build up on the mating surface of the wheel hubs. If this surface is not cleaned between wheel changes, uneven torque forces may cause wheel bolts to fracture. Although this is most likely to happen during wheel change service, it is possible that the bolts may break later while the vehicle is being driven. Correction: Dealer will clean the hub and reinstall the wheel with improved bolts and attached washers that will eliminate the clamping force reduction.

캐나다 교통부2002년 12월 23일2002247연식 1999–2003원문(영어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 II · 2009–2011
리콜보통기타UK

토우볼이 토우바에서 분리됨

내부 및 외부 힘의 복합적인 작용으로 인해 토볼(towball)이 토볼 하우징에서 예기치 않게 분리되었고, 그 결과 트레일러가 견인 차량에서 분리되었습니다.

DVSA · 영국2002년 7월 11일R/2002/093자동 번역 · 원문: 영어자세히 보기 →
9-5 I · 1997–2009
리콜보통엔진JP

過給機

ターボチャージャ(過給機)の冷却水配管継手に不適切なものがあるため、そのままの状 態で使用を続けると、タービンシャフトの冷却が不足し、最悪の場合、オイルシールが破 損して潤滑油が排気管に流出するおそれがある。

국토교통성 · 일본2000년 7월 4일1208172연식 1997–2000원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통엔진JP

ブローバイ装置

原動機のブローバイガス還元装置において、PCVバルブ(ブローバイガス流量を調整す るバルブ)の材質が不適切なため、そのままの状態で使用を続けると、当該バルブが作動 しなくなり、ブローバイガス還元装置が機能しなくなるおそれがある。

국토교통성 · 일본2000년 7월 4일1208171연식 1997–2000원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통전장JP

その他(電気装置)

原動機室内のスタータモータの電気配線コネクタに防水シールが取り付けられていないも のがあるため、そのままの状態で使用を続けると、当該コネクタ部に水分が混入し、最悪 の場合、コネクタピンが腐食して導通不良となり、原動機が始動できなくなるおそれがあ る。

국토교통성 · 일본2000년 7월 4일1208160연식 1999원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통브레이크JP

A/T

エンジンルーム内の自動変速機を制御するための電気配線において、当該電気配線の取 り回しが不適切なため、ABS機器のブラケットと接触するものがあり、そのままの状態 で使用を続けると、当該電気配線の被覆が損傷し、最悪の場合、自動変速機が適切に作動 しないおそれがある。

국토교통성 · 일본2000년 1월 20일2201430연식 1998원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
9-5 I · 1997–2009
리콜보통엔진JP

その他(エンジン)

原動機において、燃料噴射量等を制御するコンピュータのプログラムが不適切なため、そ のままの状態で使用を続けると、最悪の場合、当該原動機の停止、または、始動が困難に なるおそれがある。

국토교통성 · 일본1999년 8월 17일1207520연식 1997–1999원문(일본어)으로 표시 중 · 번역 대기자세히 보기 →
이전 →

출처: NHTSA(미국, 퍼블릭 도메인), 캐나다 교통부(Open Government Licence – Canada), DVSA(영국, Open Government Licence v3.0), RappelConso 및 EU Safety Gate(프랑스, Licence Ouverte 2.0), 일본 국토교통성(공공데이터 이용약관 1.0), 한국 국토교통부(자동차리콜센터 car.go.kr).