Boletim
A faulty electric auxiliary heater may have been installed in the certain vehicles. This could result in the failure of the electric auxiliary heater, utilized for the vehicle interior.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre BMW iX (todas as gerações)
Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.
A faulty electric auxiliary heater may have been installed in the certain vehicles. This could result in the failure of the electric auxiliary heater, utilized for the vehicle interior.
When navigation is selected, only the start animation with the text Starting navigation system... isdisplayed. The Navigation application does not start. This only applies to vehicles where Navigation hasbeen enabled and has been verified to work previously.
This is an informational bulletin regarding Plug & Charge function complaint diagnosis. Possible customer complaints: Plug & Charge menu does not appear in the vehicle, function not available Problems with the configuration, for example: Contracts cannot be installed Fault / problems when attempting charging with Plug & Charge Plug & Charge contract disappeared Plug & Charge payment method expired
There is coolant leaking from under the car Low heater output Possible Check Control message Drive, you can continue driving (ID49) Possible fault codes stored in these BEV vehicles: 224163 Electric auxiliary heater for the high-voltage battery unit: Undervoltage or internalcommunication fault 8049AA - Coolant level sensor, expansion tank: Coolant level low or short circuit to ground or linedisconnection 80124F Electric auxiliary heater: Communication in electric auxiliary heater faulty 224F60 - Coolant level sensor, expansion tank: Coolant level low or short circuit to ground or linedisconnection 224111 - Cooling system for power electronics: Coolant loss detected 224107 - Cooling system for high-voltage battery unit, component protection: Detection of coolantloss
A manufacturing defect in high-voltage cells of the high-voltage battery can result in electrolyte leakage which might result in a conductive connection with surrounding components. Depending on the contact resistance, a yellow or red Check Control message will then be displayed; it is permitted for you to continue driving, but this will result in a charging interruption during charging.
BMW Remote Software Upgrade (RSU) is not possible. The Remote Software Upgrade menu shows thefollowing text: A remote software upgrade and the activation of functions are not possible. Please contact your servicepartner to restore functionality. Additionally, certain purchased BMW ConnectedDrive Upgrades that require RSU for installation cannot be activated. After the purchase, the status of the upgrade displayed the CID remains In Activation.
RSU availability. It is possible the State of Health (SoH) of the high-voltage (HV) battery is displayed incorrectly to the customer. The value is continuously displayed as 100% regardless of the actual ageing of the HV battery.
During workshop repairs with software updates, certain customer vehicles may be changed to BMW Operating System 8.5, and returned to customers without making them aware of the change.
The I20 has a front ornamental grille with radome* heating. The radome heating is intended to melt snow deposits in cold weather to ensure the safe function of the sensors behind it. Due to a manufacturing defect in the component, the heater circuits may be interrupted, and the radome heating may fail.
After the telematics module (TCB4) has been replaced, the replacement part control unit is not accepted byISTA.
After programming the vehicle via ISTA/RSUto I-level 26-03-5xx, customer may reportsome of the interior ambient lighting strips(arrows) may begin to fail sporadically after adeep sleep cycle. This concern is temporary and the interiorambient lighting will be restored on its ownafter the vehicle is locked/unlocked or colorselection setting is changed.
Verifique a mensagem de Controlo: "Pode continuar a conduzir. A transmissão (00029) é exibida. O seguinte código de falha está armazenado na memória de falhas da CCU: 224188 Módulo do pedal do acelerador, sensor do pedal, sensor 1, sensor 2: Sinais implausíveis. Pode ou não haver uma queixa de condução associada à avaria.
The Central Information Display (CID) side of the Multifunction Display (MFD) may flicker intermittently. Theflickering manifests itself in three phases: The image is distorted The central information display turns black (black screen) The image is OK again The complete flickering episode with all the above-mentioned three phases only lasts about half a second intotal each time.
O veículo pode apresentar diversos problemas operacionais com os Modos Projetados do Apple CarPlay, tais como: Quedas de conexão Ausência de reconexão automática Erros de exibição
Charging sessions cannot be started or they are interrupted while using a Level 2 AC high-power chargingstation, or with a Level 3 DC charging station. Charging may start normally but can interrupt after some time. Level 2 (240 V) Flex Charger and Wall boxmay also be affected. The red or white LED is displayed on the high-voltage charging socket; however, no associated fault codesare stored.
Headlight Return
After starting up the vehicle, a distinct, constant, humming noise can be heard from the right area of the instrument panel.
Gen 5 BEV/PHEV vehicles may set the Combined Charging Unit (CCU) in programming abort due to no communication to the HV charge socket electronics.
Charging sessions cannot be started or they are interrupted while using a Level 2 AC high-power charging station, or with a Level 3 DC charging station. Charging may start normally but can interrupt after some time. Level 2 (240 V) Flex Charger and Wall box may also be affected. The red or white LED is displayed on the high-voltage charging socket; however, no associated fault codes are stored.
After the software update to version 25-07-5XX, existing activation points for the Automate My Habitsfunction no longer work.
High Voltage Connection Return
A manufacturing defect in a bearing of the electronic drive unit could result in bearing damage. This is caused by an unusual acoustic signal in the area of the drive unit. The bearing could fail completely at a later stage, which will be displayed to you by means of a red Check Control message. In this case, the driver is asked to call BMW Roadside Assistance.
The vehicle may experience various operational issues with the infotainment system such as: Resets of the head unit Delayed start-up of the head unit (longer than 30 seconds) Failed start-up of the head unit Sporadic or permanent problems with navigation Sporadic or permanent Bluetooth connection problems Sporadic or permanent audio problems Sporadic or permanent speech / IPA (international phonetic alphabet) problems Missing displays, radio stations, camera images or applications
O veículo pode apresentar diversos problemas operacionais com o Display Multifuncional, tais como: - Tela preta intermitente - Tela preta permanente - Funções da unidade principal não exibidas de forma intermitente (ou seja, somente a tela de Navegação fica preta)
The vehicle may experience various operational issues with the infotainment system such as: Resets of the head unit Delayed start-up of the head unit (longer than 30 seconds) Failed start-up of the head unit Sporadic or permanent problems with navigation Sporadic or permanent Bluetooth connection problems Sporadic or permanent audio problems Sporadic or permanent speech / IPA (international phonetic alphabet) problems Missing displays, radio stations, camera images or applications
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).