Boletim
Vazamento de água para o tapete proveniente do sistema de aquecimento e ar-condicionado (HVAC) após o veículo ter passado por reparos anteriores no sistema HVAC.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre BMW X6 (todas as gerações)
Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.
Vazamento de água para o tapete proveniente do sistema de aquecimento e ar-condicionado (HVAC) após o veículo ter passado por reparos anteriores no sistema HVAC.
A tampa do cabeçote não foi instalada corretamente na fábrica de montagem.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might belower than when handed over to the workshop for the repair.
Due to an implementation error in various OBD diagnostics in the vehicle's control units, in very rare cases itmay happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.
When turning the steering wheel while stationary or when driving on uneven roads; cracking, creaking, or knocking noises may be heard.
It was determined that your vehicle was fitted with a brake booster that potentially has a faulty hydraulic valve. This may result in a modified pedal feel and a sporadic red Check Control message. The brake booster should be replaced.
Various external influences can cause premature aging of the tension strut hydro-mount elastomer; which can lead to cracks in the material, and leakage.
The right rear drive shaft may not have been manufactured correctly during production and may break. In the event of a fault, you will hear significant noises in the area of the rear axle and the driving performance will be noticeably reduced. At the same time, warning lights and Check Control messages will be shown on the Central Display.
The wheel bearing and the brake disc are not correctly aligned; are not concentric (circled). When applicable work is being performed, it is therefore difficult to remove the wheel bolts from, or fasten them into the wheel bearing hub.
When turning the steering wheel while stationary or when driving on uneven roads; cracking, creaking, or knocking noises may be heard.
The seat lumbar system Massage will not function if the module needs to be initialized. This can occur toeither the drivers and/or passenger side seat. Here is a list of possible faults: Seat pneumatics module front right SPNM _ VR 025908 - SPNMVR: Control unit is not coded 02590B - SPNMVR: Control unit is not encoded for the vehicle 806927 - SPNMVR: Installation location not taught in Seat pneumatics module front left SPNM _ VL 025308 - SPNMVL: Control unit is not coded 02530B - SPNMVL: Control unit is not encoded for the vehicle 8067A7 - SPNMVL: Installation location not taught in Seat Module Driver FAS SMFA 80301E - No seat adjustment because of engine start conditions Seat Module Passenger BFS SMBF 802C1E - No seat adjustment because of engine start conditions Seat Module Drivers Side Rear FAH SMFAH 802E1E - No seat adjustment because of engine start conditions Seat Module Passenger Side Rear BFH SMBFH 802A1E - No seat adjustment because of engine start conditions
After programming from the I-Levels between 24-03-505 and lower than 24-03-540 to I-Level 24-11-530 or higher, the following CCM may be displayed: CCM-2525: Brake system. Drive at moderate speed
The air line on the air suspension supply system may not be properly installed. In the event of a fault, residual pressure is maintained in the struts and corresponding check control message.
The air line on the air suspension supply system may not be properly installed. In the event of a fault, residual pressure is maintained in the struts and corresponding check control message.
Brake groaning noises heard at the rear axle at slow speeds, i.e. close to standstill, stop and go driving;when parking or maneuvering.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
BMW AG has decided on a service campaign for certain vehicles from the G0x, G12 and G20 series. Please have the starter motor checked and, if necessary, replaced in the vehicles concerned (according to the vehicle identification number selection) if possible before vehicle delivery. If vehicles have already been delivered, please have the measure carried out the next time the vehicles enter the workshop. A bolting fault on the long bolt screws can cause the magnets in the starter motor to twist. As a result, the power of the starter motor decreases. As a result, the engine does not start.
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might be lower than when handed over to the workshop for the repair.
Improved diagnostic software for the brake system.
Due to an installation error, the crankshaft sensor connector may not have been properly locked. In very rare cases, the plug connection may become disconnected. If no signal is sent by the crankshaftsensor, the engine will switch to emergency operation and a Check Control message will occur.
There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages.
Please have the starter motor checked and, if necessary, replaced in the vehicles concerned (according tothe vehicle identification number selection) if possible before vehicle delivery. If vehicles have already been delivered, please have the measure carried out the next time the vehiclesenter the workshop. A bolting fault on the long bolt screws can cause the magnets in the starter motor to twist. As a result, thepower of the starter motor decreases. As a result, the engine does not start.
There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages.
Incorrect adjustment of the front and rear axles may result in steering wheel drift or increased tire wear onthe vehicle.
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).