Seat belts:Rear/other
Certain passenger vehicles fail to conform to federal motor vehicle safety standard no. 210, 'seat belt assembly anchorages.' the passenger-side rear safety belt may have been installed with an incorrect nut and bolt.
Certain passenger vehicles fail to conform to federal motor vehicle safety standard no. 210, 'seat belt assembly anchorages.' the passenger-side rear safety belt may have been installed with an incorrect nut and bolt.
Em certos veículos de passeio. Se o motor não pegar e o condutor mantiver a chave na posição "start" por um período prolongado, uma corrente elevada passa pelo interruptor de ignição e, por vezes, gera calor suficiente para derreter peças internas do interruptor.
Certos veículos, após serem expostos a quantidades substanciais de água, podem sofrer o acionamento do airbag frontal do motorista ou do passageiro sem que tenha ocorrido uma colisão. O manual do proprietário desses veículos não fornece informações específicas sobre essa situação. O acionamento inadvertido do airbag frontal do motorista e/ou do passageiro em uma situação sem acidente (sem impacto) pode causar danos ao ambiente ao redor do veículo (para-brisa / painel de instrumentos) e gerar reparos caros, incluindo a substituição do(s) módulo(s) do airbag e do Módulo de Detecção e Diagnóstico (SDM). Em alguns casos, o acionamento inadvertido pode causar lesões leves aos ocupantes do veículo. Correção: a GM notificará os proprietários desses veículos 1996 e 1997 sobre o potencial efeito do acúmulo de água no interior do veículo sobre o funcionamento do sistema de airbag (conforme incluído nos manuais do proprietário dos veículos dos anos-modelo 1998 e posteriores).
Em certos veículos de passageiros. Se o motor não pegar e o condutor mantiver a chave na posição "start" por um período prolongado, uma corrente elevada passa pelo interruptor de ignição e, por vezes, gera calor suficiente para derreter peças internas do interruptor.
Vehicle description: Passenger vehicles equipped with bi-fuel compressed natural gas (cng) vehicles. The cng fuel line and the cng high pressure regulator coolant lines can contact other fuel (gasoline) and brake lines on the vehicle. Abrasion from contact can cause a leak in the brake pipe, fuel pipe, or both.
Vehicle description: Passenger vehicles. The wheel lug nuts were not tightened securely resulting in a fracture of the wheel studs.
Vehicle description: Passenger vehicles. The compact spare tire assemblies were assembled with incorrect rims. If the spare tire is underinflated, the bead can separate from the rim causing a rapid loss of air. This does not comply with the requirements of fmvss no. 110, "tire selection and rims."
Vehicles do not comply with c.M.V.S.S.210- seat belt assembly anchorages. In a vehicle crash the front door interlock striker stud may fail, which could cause the door frame to collapse. This could result in the failure of the shoulder belt to provide sufficient restraint to the seat occupant. Correction: The striker studs will be replaced.
On vehicles with "daytime running lights" (d.R.L.), the d.R.L. Module, which is located near the battery, can overheat, resulting in an engine compartment fire. Correction: A non-functional module, which will render the d.R.L.'s inoperative but allow normal use of the vehicle's lighting system, will be installed until functional modules become available, at which time this recall will be reissued to have the d.R.L. System upgraded.
Small creases on the underside of the fuel tank may fatigue and crack resulting in a fuel leak. If the leak is undetected and there is an external source of ignition, a fire could result. Correction: Vehicles will be inspected and fuel tanks replaced as required.
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
On certain passenger vehicles, the rear lamps that provide stop and turn signals and tail lamp functions stop working because of inadequate contact between the bulb and socket. In addition, if one bulbs were to become inoperative while the vehicle was operating in cruise control, the cruise control would disengage when the remaining bulb was activated. If both lamps were to become inoperative, the cruise control would not engage.
Certain passenger vehicles and mini vans have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. These and some other retainers used in vehicles assembled between january 1, 1996 and october 31, 1997, could fail and permit the ball bearings to escape.
Certain vehicles do not comply with the requirements of CMVSS 101- Location and Identification of Controls and Displays. Vehicles exhibit a condition in which the "Generator Low Voltage" indicator light will not illuminate under low voltage conditions. Correction: Dealers will reflash the vehicle PCM with new calibration software.
Vehicle description: Passenger vehicles equipped with the bi-fuel option fail to comply with fmvss no. 101, "control location, identification, and illumination." the instrument panel lights in these vehicles are at full illumination levels and cannot be adjusted. The standard requires at least two levels of illumination.
Note: Certain 1997-99 vehicles in Ontario, Quebec and the Atlantic provinces and 1995-99 vehicles in all other provinces and territories. Moisture may enter the Powertrain Control Module (PCM) as a result of corrosion after extended exposure to road salt. This can lead to symptoms including illumination of the "Check Engine" light or the engine running rough. If these symptoms are ignored the engine may stall and may not be able to be restarted. Correction: Dealers will seal the Powertrain Control Module (PCM) in a protective shield/cover assembly.
Vehicle description: Passenger vehicles. These vehicles do not comply with requirements of fmvss no. 101, "control location, identification, and illumination." the instrument panel backlighting may not function after adjusting the interior light intensity.
On certain vehicles located in Ontario, Quebec, New Brunswick, Nova Scotia, Prince Edward Island and Newfoundland, Moisture entering the Powertrain Control Module (PCM) as a result of corrosion can cause illumination of the "Check Engine" light or cause the engine to run rough. If these symptoms are ignored, the engine may stall and may not be able to be restarted. Correction: Dealers will inspect, clean and/or replace the Powertrain Control Module (PCM), then seal the PCM in a protective shield/cover assembly.
Certain vehicles may have a condition which could result in one of the rear suspension trailing arm bolts breaking. If this were to occur while the vehicle was in motion, vehicle control would be affected and a crash could occur without prior warning. Correction: Dealers will replace the rear suspension trailing arm fasteners.
Vehicle description: Passenger vehicles. One of the rear suspension trailing arm bolts can fatigue and break.
Because of certain calibrations in the air bag's computer, there is an increased risk of an air bag deployment in a low speed crash or when an object strikes the floor pan. Correction: The sdm module will be recalibrated to reduce the sensitivity to short and mid-duration commanded deployments.
Vehicle description: Passenger vehicles. Because of certain calibrations in the air bag's sensing and diagnostic module, an inadvertent air bag deployment could occur in a low speed crash or when an object strikes the floor pan.
These vehicles may not comply with c.M.V.S.S. 214 - side door strength. There may be mis-located welds at the joint between the left rocker panel inner reinforcement and the body side ring. In the event of a vehicle crash, the sheet metal structure may not perform as designed. This could result in reduced levels of occupant protection. Correction: Vehicles will be inspected for mis-located welds and, if necessary, up to five welds will be placed between the involved panels.
Vehicle description: Passenger vehicles. These vehicles were built with mis-located welds at the joint between the left rocker panel inner reinforcement and the body side ring. This does not meet the requirements of fmvss no. 214, "side door strength."
Vehicle description: Passenger vehicles. These vehicles were built with the potential for the interior lamps to come on unexpectedly while the vehicles are being driven. This does not meet the requirements of fmvss no. 101, "controls and displays."
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).