On vehicles with four wheel drive and automatic locking front hubs, the front brake hose, between the body brake tubing and the front axle connector, may have been improperly installed (twisted) during vehicle assembly. If twisted, the hose can be looped upon itself in a manner that may allow abrasive contact during normal suspension travel. This could result in eventual hose failure and partial loss of braking capability. Correction: Vehicles will be inspected and brake lines rerouted if necessary.
Transport Canada3 de jul. de 19871987068Anos-modelo 1987Exibido no inglês original · tradução pendenteVer detalhes →
Certain vehicles may have been built with an improperly installed (twisted) front brake hose. This could allow abrasive contact during normal suspension travel and result in eventual hose failure and partial loss of braking capability.
Transport Canada10 de out. de 19841984122Anos-modelo 1985Exibido no inglês original · tradução pendenteVer detalhes →
Vehicles are not in compliance with the impact test requirements of federal motor vehicle safety standard 301, "fuel system integrity." the structure of the rear step bumper may not withstand a rear end collision similar to the force created in testing; fuel leakage may occur upon impact.
NHTSA · Estados Unidos24 de set. de 198484V115000Anos-modelo 1980–1985Exibido no inglês original · tradução pendenteVer detalhes →
Em determinados veículos, as transmissões automáticas podem conter um conjunto de haste do trinco de estacionamento (park sprag rod) que pode ficar preso na posição de dente encostado (sem engatar). Se isso ocorrer, o veículo pode se mover por conta própria a partir da posição de estacionado e causar uma colisão. Correção: Os veículos serão inspecionados e os conjuntos de haste do trinco de estacionamento suspeitos serão substituídos.
Transport Canada5 de jan. de 19881988002Anos-modelo 1988Traduzido automaticamente · original: inglêsVer detalhes →
On certain vehicles, the master cylinder may have been overstressed and cracked during cylinder manufacture. A cracked cylinder may fail during braking resulting in loss of vehicle braking capability. This could result in a vehicle crash without prior warning.
Transport Canada7 de fev. de 19861986020Anos-modelo 1986Exibido no inglês original · tradução pendenteVer detalhes →
The front brake hose, which is routed from the body brake tubing to the front axle connector, may have been twisted when installed. If the hose is twisted, it may become looped or coiled upon itself resulting in abrasive contact during normal operation.
NHTSA · Estados Unidos24 de set. de 198484V117000Anos-modelo 1985Exibido no inglês original · tradução pendenteVer detalhes →
Ignition switches installed in the involved vehicles may have been distorted during a crimping operation which resulted in the internal plastic contact carrier of the switch cracking. Pieces of a cracked carrier may break away, permitting abnormal switch electrical contact and the potential for starter actuaton when the switch is turned to the accessory position.
NHTSA · Estados Unidos5 de out. de 198282V095000Anos-modelo 1983Exibido no inglês original · tradução pendenteVer detalhes →
Clamp bolts installed on certain vehicles may contain cracks. Eventually these bolts may break through, causing separation of the ball joint from the steering knuckle.
NHTSA · Estados Unidos27 de mai. de 198282V055000Anos-modelo 1982Exibido no inglês original · tradução pendenteVer detalhes →
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).