Em determinados veículos de passageiros equipados com motores de 2,4 litros, a mangueira de alta pressão da direção hidráulica pode envelhecer prematuramente por calor e desenvolver um vazamento.
NHTSA · Estados Unidos5 de jan. de 200606V001000Anos-modelo 1999–2000Traduzido automaticamente · original: inglêsVer detalhes →
Vehicle description: Passenger vehicles. Some of these vehicles may have been built with an inadequate weld between the right front brake hose block and the stand-off bracket.
NHTSA · Estados Unidos17 de jul. de 200000V196000Anos-modelo 2000Exibido no inglês original · tradução pendenteVer detalhes →
Vehicle description: Passenger vehicles. The rear seat belt anchor does not achieve the loading required by fmvss no. 210, "seat belt assembly anchorages."
NHTSA · Estados Unidos20 de mar. de 199898V063000Anos-modelo 1995Exibido no inglês original · tradução pendenteVer detalhes →
An engine cylinder head oil galley plug may not be adequately retained. Inadequate retention of the plug may result in oil leakage which could potentially cause a fire in the engine compartment. Correction: An expansion plug and retaining bracket will be installed over the suspect cylinder head oil galley plug.
Transport Canada10 de jan. de 19961996009Anos-modelo 1995–1996Exibido no inglês original · tradução pendenteVer detalhes →
Em certos veículos de passageiros, o bloqueio de ignição-estacionamento do alavanca de alavanca de piso pode falhar e permitir que o alavanca de alavanca seja movido para fora da posição de estacionamento com a chave removida. Um intertravamento inoperacional pode também permitir que a chave seja removida quando a alavanca de mudanças não foi colocada na posição de estacionamento.
NHTSA · Estados Unidos13 de jan. de 200404V021000Anos-modelo 1995–1999Traduzido automaticamente · original: inglêsVer detalhes →
On certain vehicles, incorrect weld wire, in combination with the stainless steel shell of the catalytic converter, will cause rusting at the weld joints and premature failure to the converter assembly. Correction: Dealers will replace the catalytic converter.
Transport Canada18 de jan. de 19991999009Anos-modelo 1998Exibido no inglês original · tradução pendenteVer detalhes →
Certain vehicles may not comply with CMVSS 1103 - exhaust emissions. During calibration, the purge flow monitor may have been inadvertently disabled in the area of purge flow detection. Correction: Powertrain Control Module will be reflashed with proper calibrations.
Transport Canada20 de nov. de 19981998227Anos-modelo 1996Exibido no inglês original · tradução pendenteVer detalhes →
Note: Vehicles equipped with a floor mounted automatic transmission shift lever. A combination of applying a mis-adjusted shifter release button with a low force attempt to shift out of park with the key in the locked position may break the connecting pin in the shifter. If this happens, the "ignition-park" interlock system will not function. Correction: The console shift interlock mechanism will be inspected for proper function. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a current production "self adjusting" design.
Transport Canada26 de ago. de 19981998165Anos-modelo 1995–1998Exibido no inglês original · tradução pendenteVer detalhes →
Vehicle description: Passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.
NHTSA · Estados Unidos6 de ago. de 199898V183000Anos-modelo 1995–1998Exibido no inglês original · tradução pendenteVer detalhes →
These vehicles may not comply with c.M.V.S.S. 210 - seat belt assembly anchorages. The rear seat belt anchor may not achieve the loading required by the standard during testing. Correction: The rear outboard seat belt anchor floor attachments will be inspected for orientation and repositioned if required.
Transport Canada27 de mar. de 19981998061Anos-modelo 1995Exibido no inglês original · tradução pendenteVer detalhes →
Certain vehicles do not comply with CMVSS 1103 - exhaust emissions. The calibration of the Powertrain Control Module (PCM) may fail to adequately control CO emissions. Correction: PCM will be reflashed with a new calibration.
Transport Canada21 de jan. de 19981998010Anos-modelo 1996Exibido no inglês original · tradução pendenteVer detalhes →
On certain vehicles, the lower control arm ball joint may separate due to loss of lubrication. This separation could result in loss of vehicle control and a crash without prior warning. Correction: Ball joint end housing cover seal will be inspected for leakage and the rubber boot will be inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.
Transport Canada20 de nov. de 19971997205Anos-modelo 1995–1997Exibido no inglês original · tradução pendenteVer detalhes →
The primary/secondary hood latch spring may not remain in position during hood closing, which can result in loss of both the primary and secondary latch function. Loss of hood function can result in a hood fly-up condition. Correction: The secondary hood latch spring will be replaced with one having a longer end hook.
Transport Canada19 de jun. de 19971997123Anos-modelo 1996–1997Exibido no inglês original · tradução pendenteVer detalhes →
On certain vehicles, the brake master cylinder may leak brake fluid due to a damaged double lip rear piston seal. Brake fluid leakage may result in diminished effectiveness of one portion of the split brake system. Correction: Rear brake master cylinder piston assemblies will be replaced.
Transport Canada17 de mai. de 19961996079Anos-modelo 1995–1996Exibido no inglês original · tradução pendenteVer detalhes →
Corrosion of the abs hydraulic control unit may cause the solenoid valves to stick in the open position. If either front wheel valve sticks, the vehicle may tend to deviate from a straight stop when the brakes are applied. Correction: A plate will be installed on the abs hydraulic control unit and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.
Transport Canada17 de mai. de 19961996078Anos-modelo 1995–1996Exibido no inglês original · tradução pendenteVer detalhes →
Descrição do veículo: Certos veículos de passageiros, caminhonetes e utilitários esportivos não atendem aos requisitos da FMVSS nº 225, "child restraint anchorage systems." Alguns dos manuais do proprietário desses veículos não contêm instruções que forneçam um procedimento passo a passo, incluindo diagramas, para a correta fixação da cinta de ancoragem (tether) do sistema de retenção infantil ao ponto de ancoragem superior.
NHTSA · Estados Unidos9 de nov. de 200000V366000Anos-modelo 2000Traduzido automaticamente · original: inglêsVer detalhes →
Vehicle description: Passenger vehicles. The affected vehicles were built with incorrect child lock instruction labels.
NHTSA · Estados Unidos2 de mar. de 200000V066000Anos-modelo 2000Exibido no inglês original · tradução pendenteVer detalhes →
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).