Sistema elétrico:Ignição
A chave de ignição pode sofrer um curto-circuito interno.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Ford EXP (todas as gerações)
A chave de ignição pode sofrer um curto-circuito interno.
Um curto-circuito pode se desenvolver no interruptor de ignição, o que pode levar a superaquecimento, fumaça e, possivelmente, incêndio na coluna de direção do veículo. Essa condição pode ocorrer com o veículo em uso ou estacionado sem supervisão. Correção: o interruptor de ignição será substituído por um interruptor de design revisado.
Em modelos de 1984, podem surgir rachaduras externas nos cabeçotes do motor, o que pode resultar em vazamento de óleo sobre o coletor de escape. Em modelos de 1985, a junta da tampa de válvulas do motor pode rachar, o que pode permitir que o óleo vaze sobre o coletor de escape. Ambas as condições criam a possibilidade de o óleo entrar em ignição, causando um incêndio no compartimento do motor. Correção: Em modelos de 1984, os cabeçotes do cilindro serão inspecionados e substituídos caso sejam encontradas rachaduras externas. Em modelos de 1985, as juntas da tampa de válvulas serão inspecionadas e substituídas, a menos que sejam de um projeto mais recente.
Rachaduras externas acima do cilindro número 3 (modelos 1984) ou rachaduras na junta da tampa dos balancins (modelos 1985) podem permitir que óleo vaze para o coletor de escape.
Os veículos podem apresentar folga inadequada entre os tubos de freio dianteiros direitos e um suporte fixado ao motor. Em determinadas condições, o suporte pode entrar em contato com o tubo metálico do freio e causar abrasão no tubo, o que poderia resultar em perda de fluido de freio e perda parcial de frenagem. Isso acarretaria o aumento das distâncias de parada.
The front sleeve bushings of the cooling fan motors are susceptible to excessive corrosion in areas of high road salt use. This may increase the rotational friction of the fan motor or result in seizure of the armature shaft to the bushing. Either condition may draw current in excess of that of a normally operating motor but less than required to operate the fuse link. This could overheat the motor wiring circuitry and possibly result in an underhood or instrument panel fire. Vehicles affected: Cars not equipped with factory air conditioning. Quebec and atlantic provinces only.
Estes veículos podem não estar em conformidade com a C.M.V.S.S. 1103 - emissões de gases de escapamento. O injetor central de combustível (CFI) pode operar com mistura rica em determinadas condições de funcionamento. Correção: Serão instalados injetores de combustível CFI aprimorados e a rotação em marcha lenta será ajustada.
These vehicles do not comply with cmvss 1103 - exhaust emissions. Vehicles affected: 1.6 l engine and atx transmissions
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
Two door models. Fatigue cracks may occur in the door lock pillars at the front door latch striker reinforcement attachment locations. The fatigue cracks may propogate to the extent that the structural integrity of the door latch striker attachment may be significantly reduced creating the possibility that the door may not be securely retained. This condition is observable by visibly noticeable cracks on the door lock pillar adjacent to the striker assemblies.
Door lock pillars could develop fatigue cracks from normal usage of door, at the point where door latch striker reinforcements are attached.
On the involved vehicles, a thermal limiter in the blower motor resistor circuit of the air conditioner/heater assembly may not function as intended. If the blower motor becomes jammed when the system is operating in the medium-low blower speed, the resistor coils can overheat causing melting and possible ignition.
Vehicles with optional air conditioning. The air conditioner blower motor thermal limiter may not operate as intended when there is a motor blockage or malfunction. Thus, if the blower motor becomes jammed when the system is operating in the medium-low blower speed mode, the resistor coils may overheat causing melting and possible ignition of the polyproplene evaporator housing with associated vehicle damage.
Vehicles equipped with power brakes. Power brake boosters may have bewen improperly assembled by supplier. Mis-indexing of rear shell of some boosters relative to the front shell may have resulted in inadequate crimping of the two shells. If booster were to separate during vehicle operation, complete loss of service brakes would result.
Some vehicles equipped with power brake boosters have front and rear shells that may have been improperly joined. Improperly joined booster shells may separate either partially or completely during brake application.
Vehicle may not meet the fuel spillage requirements of cmvss 301 - fuel system integrity.
Certain vehicles may not meet applicable minimum fuel spillage requirements of federal motor vehicle safety standard no. 301, "fuel system integrity". During a 30 mph rear impact test, fuel spillage limits were exceeded by vehicle.
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).