O haste da válvula de controlo do aquecedor não cumpre as especificações de material. Temperaturas elevadas do líquido de arrefecimento podem fazer com que a haste apresente fugas.
NHTSA · Estados Unidos6 de jun. de 199494V103000Anos-modelo 1988–1989Traduzido automaticamente · original: inglêsVer detalhes →
The veículos não atenderam aos requisitos do teste de impacto lateral com barreira móvel da FMVSS 301, "integridade do sistema de combustível". O vazamento de combustível do tanque excedeu a quantidade máxima permitida de derramamento.
NHTSA · Estados Unidos23 de nov. de 199393V192000Anos-modelo 1990–1994Traduzido automaticamente · original: inglêsVer detalhes →
Note: All 1988-89 excel vehicles sold in canada. The reed valve subassembly contained within the air control valve could fail due to corrosion allowing the hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot gases may melt the secondary air filter case and could result in an engine compartment fire. Correction: Reed valve subassembly will be replaced.
Transport Canada30 de dez. de 19911991176Anos-modelo 1988–1989Exibido no inglês original · tradução pendenteVer detalhes →
The fuel return tube clip may have been incorrectly installed allowing the fuel return hose to contact either the distributor high tension cable or the e.G.R. Valve. This could, over time, result in wear and eventual leakage at the fuel hose. The fuel leakage could result in an underhood fire. V.I.N. Range s.O.P. To kmhla31j1gu040086
Transport Canada18 de abr. de 19861986044Anos-modelo 1986Exibido no inglês original · tradução pendenteVer detalhes →
In some vehicles, the manufacturer's protective internal coating of the electronic crank angle sensor does not meet specifications, which can cause an open circuit at high operating temperatures. This can cause the vehicle to stall.
NHTSA · Estados Unidos11 de mai. de 199494V090000Anos-modelo 1994Exibido no inglês original · tradução pendenteVer detalhes →
As transmissões manuais podem travar devido à lubrificação insuficiente das engrenagens na caixa de transmissão. Isso pode fazer com que as rodas motrizes travem e o veículo pare repentinamente.
NHTSA · Estados Unidos4 de out. de 199393V167000Anos-modelo 1986–1989Traduzido automaticamente · original: inglêsVer detalhes →
Deterioration of the reed valve subassembly may lead to a malfunction within the secondary air supply portion of the emission control system. The screws which attach the reeds to the reed valve subassembly may rust, and if the rusting becomes severe, the screw heads will erode and allow the reeds to separate from the reed valve subassembly. Corrosion may also occur on the reed valve subassembly, deforming the reed seats and preventing the reeds from closing properly. Separation of the reeds from the reed valve subassembly or improper closing of the reeds allow hot exhaust gases to flow backward into the plastic secondary air filter case when the vehicle is being driven. These hot exhaust gases may melt the secondary plastic air filter case.
NHTSA · Estados Unidos31 de dez. de 199191V225000Anos-modelo 1986–1989Exibido no inglês original · tradução pendenteVer detalhes →
The lock washer located under the nut that secures the front hub to the driveshaft may crack due to improper heat treatment. This could result in wheel bearing freeplay and bearing damage with possible wheel lock-up or brake caliper knockback. Correction: Washer will be replaced note: All units have been corrected.
Transport Canada18 de mai. de 19901990072Anos-modelo 1990Exibido no inglês original · tradução pendenteVer detalhes →
The possibility exists that under certain braking conditions, front brake fade may occur,thus reducing braking effectiveness. Correction: Improved semi-metallic brake pads will be installed.
Transport Canada27 de nov. de 19871987127Anos-modelo 1986–1987Exibido no inglês original · tradução pendenteVer detalhes →
The cotter pin that retains the brake clevis pin may have been omitted or incorrectly installed. If the cotter pin was omitted or if it were to fall out of the clevis pin,the vehicles' brakes would be subject to failure without warning.
Transport Canada29 de mar. de 19861986033Anos-modelo 1986Exibido no inglês original · tradução pendenteVer detalhes →
A cotter pin in the brake pedal to brake master cylinder linkage assembly may be missing. This pin acts as a retainer for the brake master cylinder pushrod clevis pin. Consequence of defect: The clevis pin may slide out causing the master cylinder/brake pedal linkage to become disengaged. If this linkage becomes disengaged the service brakes cannot be applied, creating the risk of a crash without prior warning.
NHTSA · Estados Unidos17 de mar. de 198686V043000Anos-modelo 1986Exibido no inglês original · tradução pendenteVer detalhes →
If cruise control main switch is in the on position when engine is started, system can be affected by a short duration voltage drop caused by optional hi-power (h340) radio.
NHTSA · Estados Unidos19 de jun. de 198989V100000Anos-modelo 1986–1989Exibido no inglês original · tradução pendenteVer detalhes →
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).