**Problema:** Este recall refere-se a determinados kits de aquecedor do bloco do motor instalados em determinados veículos ou vendidos como acessórios nas concessionárias Toyota ou Lexus. Em alguns veículos, o cabo do aquecedor do bloco do motor pode não ter proteção térmica suficiente e ser danificado por altas temperaturas. Se isso acontecer, o cabo pode sofrer um curto-circuito enquanto estiver conectado à tomada, fazendo com que a fiação superaqueça ou derreta.
**Nota:** Este recall afeta apenas os seguintes números de peça do aquecedor/cabo de alimentação: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903
**Risco à segurança:** A fiação do aquecedor do bloco do motor que superaquece ou derrete pode criar o risco de incêndio.
**Ações corretivas:** A Toyota recomenda que você pare de usar o aquecedor do bloco do motor imediatamente. A Toyota notificará os proprietários por correspondência e instruirá a levar o veículo a uma concessionária para desativar o aquecedor do bloco do motor. Para alguns veículos, as ações corretivas para este recall ainda estão em desenvolvimento. Para outros, não é possível instalar um novo aquecedor do bloco do motor, e o proprietário receberá o reembolso do preço de compra do aquecedor do bloco do motor.
Transport Canada24 de nov. de 20212021723Anos-modelo 2012–2017Traduzido automaticamente · original: inglêsVer detalhes →
There is a possibility that the resin weld between the fuel tank and the fuel inlet pipe may be insufficient because the fuel tank and fuel inlet pipe were misaligned during the manufacturing process.
DVSA · Reino Unido22 de jan. de 2018R/2017/332Anos-modelo 2016–2017Exibido no inglês original · tradução pendenteVer detalhes →
On certain vehicles, the electrical power cords of some dealer installed block heaters may have been improperly manufactured, causing the wires to contact each other, resulting in a short circuit. A short circuit could lead to a fire which would increase the risk of injury and/or damage to property. Correction: For vehicles where the subject block heater was approved for installation, the dealer will replace the block heater assembly with a new one of an improved design. For vehicles where the subject block heater was not approved for installation, dealers will remove the block heater assembly. In the interim, until the remedy can be performed, dealers will cut the plug end from the block heater cord to disable the block heater's operation.
Transport Canada20 de jul. de 20172017363Anos-modelo 2016–2017Exibido no inglês original · tradução pendenteVer detalhes →
null A crack could develop in the fuel evaporative emission control unit which is attached to the fuel tank. When the fuel tank is full, fuel could leak from the crack which, in the presence of an ignition source, could lead to a vehicle fire.
Safety Gate · UE5 de jul. de 2016A12/0849/16Anos-modelo 2009–2015Exibido no inglês original · tradução pendenteVer detalhes →
null Welded parts of the inflator in each of the curtain shield air bags could have a minute crack. If the crack propagates over time, part of the inflator could separate causing compressed gas to escape. This would result in partial inflation of the curtain shield air bag, and, in limited circumstances, one or both sections of the inflator could enter the interior of the vehicle. If an occupant is present in the vehicle, this could lead to injuries.
Safety Gate · UE5 de jul. de 2016A12/0848/16Anos-modelo 2009–2012Exibido no inglês original · tradução pendenteVer detalhes →
On certain vehicles, a defect in the curtain shield airbags could cause the inflator to fail, releasing pressurized gas into the airbag, partially inflating it. If this occurs, parts of the inflator could also separate from the vehicle structure, entering the interior of the vehicle. Should this occur when occupants are in the vehicle, unintended airbag deployment could startle the driver, and airbag inflator parts could come into contact with the occupants, increasing the risk of injury and a crash. Correction: Dealers will install a retention bracket which will prevent the inflator parts from entering the vehicle interior.
Transport Canada29 de jun. de 20162016335Anos-modelo 2011–2012Exibido no inglês original · tradução pendenteVer detalhes →
No sistema híbrido, devido à insuficiente imunidade a ruído elétrico da placa de controle do módulo de conversão de energia, o ruído elétrico gerado por variações de tensão no circuito de alta tensão pode ser interpretado pelo circuito de controle de energia como uma anomalia, levando a uma parada momentânea. Por esse motivo, a tensão de alimentação pode cair por um instante, havendo risco de perda temporária de potência acompanhada da acendimento da luz de advertência do motor.
jp1 de jun. de 20211149660Anos-modelo 2020–2021Traduzido automaticamente · original: japonêsVer detalhes →
Due to an error in the manufacturing process, micro-cracks may develop on the plating of the damper rod on the rear door, allowing the gas charged in the damper to leak. If a sufficient amount of gas leaks, the damper may fail to keep the back door open, increasing the risk of injury.
Safety Gate · UE24 de out. de 2019A12/1634/19Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
jp17 de out. de 20192105800Anos-modelo 2019Exibido no japonês original · tradução pendenteVer detalhes →
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0).