Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · boletim do fabricante10199641Anos-modelo 2021Exibido no inglês original · tradução pendenteVer detalhes →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · boletim do fabricante10185813Anos-modelo 2017Exibido no inglês original · tradução pendenteVer detalhes →
Alguns clientes podem reclamar de qualquer um dos seguintes itens:
1. A tela da central multimídia não fornece o Código de Autorização (OTP) durante o registro do veículo conectado no aplicativo MyMazda.
2. Função(ões) remota(s) inoperante(s).
Alguns veículos podem apresentar a luz de verificação do motor (Check Engine) acesa, com o código DTC P0300:00 (Falha de ignição aleatória detectada) armazenado. Isso pode ser causado por uma detecção incorreta de falha de ignição devido a uma lógica de controle do PCM inadequada. Para eliminar esse problema, a lógica de controle do PCM foi modificada.
Alguns clientes podem notar que a luz de carga acende durante a condução. Ao realizar a inspeção, o DTC P2502:00 PCM (Falha na tensão gerada pelo alternador) fica armazenado na memória. Isso pode ser causado por resistência entre a placa de circuito e o terra. Quando passa corrente elétrica de alta intensidade, a posição do terminal de terra pode não ser suficiente. Para eliminar essa preocupação, o software de controle do conversor CC-CC foi modificado. Além disso, o procedimento de produção foi revisado. O torque de aperto do terminal de terra e da placa de circuito foi aumentado.
Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
NHTSA · boletim do fabricante11008417Anos-modelo 2021Exibido no inglês original · tradução pendenteVer detalhes →
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
NHTSA · boletim do fabricante10190951Anos-modelo 2021Exibido no inglês original · tradução pendenteVer detalhes →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · boletim do fabricante10180595Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · boletim do fabricante10186918Anos-modelo 2017Exibido no inglês original · tradução pendenteVer detalhes →
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.
NHTSA · boletim do fabricante10186257Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
NHTSA · boletim do fabricante10144332Anos-modelo 2018Exibido no inglês original · tradução pendenteVer detalhes →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · boletim do fabricante10105642Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · boletim do fabricante10101468Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · boletim do fabricante10091601Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · boletim do fabricante10090667Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.
NHTSA · boletim do fabricante10076685Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
Mazda: There is condensation and fog in the front and rear combination lights. *rm
NHTSA · boletim do fabricante10037655Anos-modelo 2011Exibido no inglês original · tradução pendenteVer detalhes →
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).