Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

Mazda MX-5

1989– · 4 gerações · 35 defeitos documentados · 4 mercados
Gerações

Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.

Ano do modelo
MX-5 (ND) · 2015–
BoletimCríticoMotorNA

Boletim

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · boletim do fabricante10153311Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoCarroceriaNA

Boletim

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.

NHTSA · boletim do fabricante11034436Anos-modelo 2020Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoMotorNA

Boletim

Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

NHTSA · boletim do fabricante10238663Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · boletim do fabricante10222563Anos-modelo 2023Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoFreiosNA

Boletim

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · boletim do fabricante10218722Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoFreiosNA

Boletim

Clunk/Rattle noise from rear brake

NHTSA · boletim do fabricante10213396Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoCarroceriaNA

Boletim

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · boletim do fabricante10185957Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoOutroNA

Boletim

Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

NHTSA · boletim do fabricante10185955Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoElétricaNA

Boletim

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · boletim do fabricante10186337Anos-modelo 2016Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoElétricaNA

Boletim

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · boletim do fabricante10185813Anos-modelo 2017Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoMotorNA

Boletim

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NHTSA · boletim do fabricante10165676Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoCarroceriaNA

Boletim

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · boletim do fabricante10165350Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoOutroNA

Boletim

Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

NHTSA · boletim do fabricante10163333Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoOutroNA

Boletim

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · boletim do fabricante10159199Anos-modelo 2018–2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · boletim do fabricante10159196Anos-modelo 2018–2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoOutroNA

Boletim

Em apoio à nova distribuição MRT, a Mazda enviará aos concessionários um novo Detector de Vazamentos de Diagnóstico de Dupla Finalidade a partir de março de 2019. Os vídeos de treinamento serão publicados no MGSS em breve, e os procedimentos do Manual de Oficina serão revisados gradualmente.

NHTSA · boletim do fabricante10154879Anos-modelo 2019Traduzido automaticamente · original: inglêsVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · boletim do fabricante10154528Anos-modelo 2018–2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · boletim do fabricante10154531Anos-modelo 2018–2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

Se um veículo apresentar vibração na carroceria ou trepidação do volante durante a condução e a causa raiz for determinada como balanceamento dos pneus, rebalanceie os pneus usando uma máquina de balanceamento Hunter GSP9700 ou equivalente. Se a sua concessionária não tiver uma máquina de balanceamento GSP9700 ou equivalente, encaminhe o veículo para reparo em outra oficina. Para encontrar a localização de uma GSP9700 perto da sua concessionária, visite o site da Hunter em www.gsp9700.com e clique em "Localize um Balanceador Road Force GSP9700".

NHTSA · boletim do fabricante10154139Anos-modelo 2019Traduzido automaticamente · original: inglêsVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoFreiosNA

Boletim

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · boletim do fabricante10153227Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoInteriorNA

Boletim

This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.

NHTSA · boletim do fabricante10153329Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoOutroNA

Boletim

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · boletim do fabricante10153331Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · boletim do fabricante10153226Anos-modelo 2018–2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoElétricaNA

Boletim

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NHTSA · boletim do fabricante10153310Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
MX-5 (ND) · 2015–
BoletimModeradoSuspensãoNA

Boletim

The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

NHTSA · boletim do fabricante10153313Anos-modelo 2019Exibido no inglês original · tradução pendenteVer detalhes →
Mais antigos →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).