Leitura livre · conta gratuita para contribuirSucessor do Anticars (2000)

MercuryMercury Capri

1979–1994 · 2 gerações · 9 defeitos documentados · 1 mercados
Gerações
Ano do modelo
MercadoTodosNA
Capri II · 1979–1986
RecallCríticoInteriorNA

Assentos e Sistemas de Retenção

A exposição prolongada à luz solar pode fazer com que a luva plástica do conjunto da lingueta do cinto de segurança dianteiro, que retém a barra de travamento, se deteriore e saia da posição. Isso pode resultar na separação da lingueta da fita do cinto de segurança, tornando o cinto inútil para o ocupante do veículo. Correção: os proprietários serão informados de que a Ford fará o reparo dos cintos de segurança que apresentarem essa condição.

Transport Canada28 de set. de 19921992117Anos-modelo 1984–1985Traduzido automaticamente · original: inglêsVer detalhes →
Capri II · 1979–1986
RecallCríticoInteriorNA

Seat belts:Front:Anchorage

The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.

NHTSA · Estados Unidos29 de abr. de 199292V063000Anos-modelo 1984–1985Exibido no inglês original · tradução pendenteVer detalhes →
Capri III · 1991–1994
RecallModeradoInteriorNA

Airbags

Os módulos de airbag não atendem às especificações da Ford para desempenho em altas temperaturas ambiente.

NHTSA · Estados Unidos2 de jun. de 199292V080000Anos-modelo 1991–1992Traduzido automaticamente · original: inglêsVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Seats And Restraints

The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.

Transport Canada17 de mai. de 19881988066Anos-modelo 1981–1983Exibido no inglês original · tradução pendenteVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Seat belts:Front:Anchorage

The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".

NHTSA · Estados Unidos20 de dez. de 198383V134000Anos-modelo 1984Exibido no inglês original · tradução pendenteVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Recall

The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.

Transport Canada17 de dez. de 19831983114Anos-modelo 1984Exibido no inglês original · tradução pendenteVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Recall

These vehicles do not comply with cmvss 209 - seat belt assemblies.

Transport Canada20 de dez. de 19821982102Anos-modelo 1980–1981Exibido no inglês original · tradução pendenteVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Seats:Front assembly:Recliner

The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.

NHTSA · Estados Unidos8 de set. de 198181V102000Anos-modelo 1981Exibido no inglês original · tradução pendenteVer detalhes →
Capri II · 1979–1986
RecallModeradoInteriorNA

Recall

Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.

Transport Canada4 de set. de 19811981092Anos-modelo 1981Exibido no inglês original · tradução pendenteVer detalhes →

Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).